Bedienungsanleitung Argo Emix (Seite 24 von 29) (Englisch)

665482

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

When Emix Tank unit is correctly connected and electrically powered the RED LED is ON (stand by).

Power ON / OFF of Emix Tank

To switch on Emix Tank, push and hold the BUTTON for about 4 seconds until the RED LED turns off and the GREEN

LEDs of water temperature light up. Emix Tank unit is designed to be always ON.

To switch off Emix Tank, push and hold the BUTTON for about 4 seconds until the GREEN LEDs turn off and only the RED

LED stays on. At this point release the BUTTON.

Once turned on, Emix Tank unit displays the temperature inside the tank.

Desired temperature setting (setpoint)

Press and quickly release repeatedly the BUTTON until the led corresponding to the desired temperature lights up (see

table). After 5 seconds without any operation, Emix Tank exits the desired temperature setting procedure and begins to

display the water temperature in the tank.

Super Booster mode activation

When the Super Booster mode is activated, all the electrical heaters will be activated at the same time, together with the

heat pump.

When the setpoint is reached, all electrical heaters are switched off and the Super Booster mode is automatically turned

off.

To activate the Super Booster mode, press and hold the BUTTON until the BLUE LED lights up.

At this point release BUTTON.

3 consecutive beeps con rm the setting.

To deactivate the Super Booster mode, press and hold the BUTTON until the GREEN LEDs turn off and the BLUE LED

lights up. At this point release BUTTON.

3 consecutive beeps con rm the deactivation.

HOW TO USE EMIX TANK

NOTE

By default, the Booster mode is off.

NOTE

By default, the Super Booster mode is off.

EMIX TANK CONFIGURATION

When Emix Tank is on, you can change the setting of some parameters.

To enter the con guration menu, press and hold the BUTTON until the BLUE, YELLOW and RED LEDs light up contem-

porary. At this point release the BUTTON.

After 5 seconds without any operation, Emix Tank exits the con guration procedure and returns to the previous menu.

Booster mode setting

The use of electrical heating elements installed in the storage tank allows you to heat the cold water faster and to reach

the desired water temperature even in conditions of very low external temperatures.

When you activate the Booster mode, the software will automatically handle the electrical heaters.

If after 120‘ from start up of the system the water setpoint is not reached, the  rst electrical element is automatically

activated. The second element will be activated after 120‘ following the course of the water temperature, until reaching

the setpoint.

To activate / deactivate the Booster mode, enter the con guration menu, then quickly press the BUTTON until the only

BLUE LED is  ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press the BUTTON once more.

3 consecutive beeps con rm the setting.

If the button is not pressed, after a few seconds the display will return to the main menu without making any setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Emix Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Emix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info