Bedienungsanleitung Argo Emix (Seite 25 von 29) (Englisch)

665482

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Setpoint limit setting with Heat Pump

It is possible to set the maximum achievable setpoint only with the Heat Pump. This limit can be set to 50°C or 58°C.

To change the setting, enter the con guration menu, then quickly press the BUTTON until the BLUE and YELLOW LEDs

are  ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press the BUTTON once more.

3 consecutive beeps con rm the setting.

If the button is not pressed, after a few seconds the display will return to the main menu without making any setting.

NOTE

By default the limit is set to 50°C. We recommend to keep this setting to optimize the energy ef ciency of Emix Tank.

Antilegionella cycle setting

To activate / deactivate the Antilegionella cycle, enter the con guration menu, then quickly press the BUTTON until the

only YELLOW LED is  ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press the BUTTON once more.

3 consecutive beeps con rm the setting.

If the button is not pressed, after a few seconds the display will return to the main menu without making any setting.

NOTE

By default, the Antilegionella cycle is on. If the cycle is turned off, the MANUFACTURER can not be held responsible.

For details on the operation of the Antilegionella cycle, see section “ANTILEGIONELLA CYCLE”.

Temperature delta setting for restart of the heat pump

When the water temperature reaches the set value or the maximum achievable value with the heat pump alone (in the

case of Emix Tank operation without other indoor units), the heat pump switches off and starts up again only when the

water temperature drops below the desired temperature of a certain value (delta).

You can change the startup delta of the heat pump by setting it to 5°C or 10°C.

To change the set value, enter the con guration menu, then quickly press the BUTTON until the BLUE and RED LEDs

are  ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press the BUTTON once more.

3 consecutive beeps con rm the setting.

If the button is not pressed, after a few seconds the display will return to the main menu without making any setting.

NOTE

By default the startup delta of the heat pump is set to 10°C. We recommend to keep this setting to optimize the energy

ef ciency of Emix Tank.

Reset of the factory settings

To reset all the factory settings, enter the con guration menu, then quickly press the BUTTON until the BLUE, YELLOW

and RED LEDs are  ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press the BUTTON once more.

3 consecutive beeps con rm the reset of factory settings.

If the button is not pressed, after a few seconds the display will return to the main menu without making any setting.

Stratiﬁ cation sensor selection

Emix Tank measures the water temperature in the tank through one of the two strati cation sensors.

It is possible to select which of the two sensors is read for the measurement.

To change the sensor, enter the con guration menu, then quickly press the BUTTON until the YELLOW and RED LEDs

are  ashing.

Then wait a few seconds until all the 5 GREEN LEDs light up and press the BUTTON once more.

3 consecutive beeps con rm the setting.

If the button is not pressed, after a few seconds the display will return to the main menu without making any setting.

NOTE

By default the selected strati cation sensor is the upper one.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Emix Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Emix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info