Bedienungsanleitung Argo Emix (Seite 14 von 30) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Finnisch)

665482

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Supply power wire A / supply power wire for electrical heaters C:

Multipolar electric wire. Size and length of the suggested electric wire are showed on table. The wire must be

Mod. H07RN-F (according to CEI 20-19 CENELEC HD 22). Make sure the length of the conductors between the

fixing point and the terminals allows the straining of the conductors L, N before that of the grounding.

Connecting wire B (SHIELDED):

Bipolar electric shielded wire; size and length of the suggested electric wire are showed in the installation manual

of outdoor unit (consider Emix as an indoor unit).

The wires have not to be lighter than Mod. H05VVC4V5-K (according to CEI 20-20 CENELEC HD21).

A B C

L ( m ) S ( mm2) L ( m ) S ( mm2) L ( m ) S ( mm2)

15 4SEE OUT.UNIT 0,75 15 425 A

Connection of electrical heater elements

You must connect at least one electrical heater element of the tank to Emix.

Failure to connect at least one electrical heater element could affect the proper operation of the system; besides this, in

case of failure of outdoor unit, the electrical heaters provide heating of the water.

Connect the Electrical Heaters of the external tank to the proper connection block (ELECTRICAL HEATER R1, R2, R3 and

Neutral); Emix supports up to three Electrical elements of 1500 W each one; for connections to three-phase tanks, use

R1,R2 and R3 as the command of an electrical panel with circuit breakers.

NOTE: Emix electrical consumption is very low (max. 100W) but in case electrical heater elements are connected, Emix

has to support the ow of big amount of electrical energy; for that reason it is necessary to power Emix independently

(phase, neutral and ground) from the outdoor unit.

Back up electrical heaters’ number setting

The setting of the switch SW1 determines the number of the con-

nected electrical heater elements or the maximum number of elec-

trical heater elements that you want to use. This operation is man-

datory.

Factory setting

to be modied

1 element

Max

1,5kW

2 elements

Max

1,5 +1,5kW

3 elements

Max

1,5 + 1,5 +

1,5kW

ELECTRICAL HEATERS WIRING DIAGRAM

1 connected element More connected elements

LENGTH, SIZE OF WIRES AND DELAYED FUSE

Connection and maintenance of the supply power wire

• The electrical connection of the unit is type Y.

• The installation of the wire must be done by qualied personnel.

• If the wire is damaged by the use, for the replacement, contact After Sale Service or qualied personnel.

• The cable glands must be tightened with the proper torque to ensure IPX1 protection and to prevent the wire from

being pushed or pulled, causing dangerous situations (100N; 0.35Nm). The cable glands of the electrical resistances’

outputs must be closed with appropriate caps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Emix Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Emix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info