Bedienungsanleitung Argo Khors (Seite 16 von 23) (Englisch)

805028

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

V 11/21

ON/OFF BUTTON

Press this button to switch the unit on or off. When switched on, the device will emit an audible signal and will begin to

operate according to the latest settings (Memory function).

MODE SELECTION BUTTON (MODE)

(on remote control and on the unit)

Press this button to select the various operating modes, according to the following sequence: Cool -> Dry -> Fan

The LEDs on the control panel will light up according to the selected mode.

In COOL mode the display lights up and the set temperature is shown (from 16 ° C to 30 ° C). In DRY and FAN modes

the display does not light up.

Remote control: Press Mode button to select the desired operation mode

In Cool mode, the temperature can be adjusted by pressing + or - buttons.

In Dry mode, the air conditioner operates in low fan speed.

In Fan mode, the fan speed can be adjusted by pressing FAN button

FAN SPEED ADJUSTMENT BUTTON

(on remote control and on the unit)

Press this button when the appliance is on to adjust the fan speed, on the control panel press the FAN button, the LED

indicators will light up at the selected speed in the following sequence: low (Low), medium (Med), high (High), automatic

(auto):

On the remote control, however, the fan speed selection sequence will be as follows:

The fan speed cannot be adjusted in DRY mode and is fixed at low.

+ - ADJUSTMENT BUTTONS

(on remote control and on the unit)

These buttons can be used to adjust the temperature and set the Timer.

The temperature can be adjusted to between 16 °C and 30 °C.

Increase temperature（+):

1) Allows for adjusting the desired temperature in cooling (COOL) mode.

2) Whenever the（

) button is pressed, the set temperature increases by 1 °C.

Decrease temperature (

1) Allows for adjusting the desired temperature in cooling (COOL) mode.

2) Whenever the (

- )

button is pressed, the set temperature decreases by 1 °C.

In dry mode, adjustments cannot be made with these buttons.

The same button allows you to set the TIMER.

By holding down the + or - button for 2 seconds on the remote control, you can quickly set the temperature.

SLEEP BUTTON

(on remote control and on the unit)

Press this button to activate the Sleep function, which automatically adapts the temperature to changes in body and room

temperature throughout the night, so as to optimise comfort when sleeping and minimise consumption.

In cooling mode, the temperature increases by 1 °C in an hour then by 2 °C in two hours, and remains in this setting for the

whole period. The Sleep function is not available in the ventilation, dehumidification and auto modes. The indicator light turns

on display whenever the Sleep function is set the LED on the display lights up, while the Sleep symbol is active on the remote

control.

The Sleep function cannot be activated in Dry (dehumidification) and Fan (ventilation) modes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Khors Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Khors

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info