Bedienungsanleitung Argo SDIAS8DC (Seite 8 von 15) (Englisch)

665477

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

A) HOW TO SET THE ON TIME

1. Press the ST button once.

The ON and time indications flash.

2. Press the H button until the designed

hour is displayed.

Press the M button until the designed

minutes are displayed. The display

will change automatically back to

show the present time after 10 sec.

3. Press the ON/OFF button to start the

air conditioner.

4. Press the button to activate the

ON timer.

B) HOW TO SET THE OFF TIME

1. Press the ST button twice.

The OFF and time indications flash.

2. Press the H button until the designed

hour is displayed.

Press the M button until the designed

minutes are displayed. The display will

change automatically back to show

the present time after 10 sec.

3. Press the ON/OFF button to start the

air conditioner.

4. Press the button two times to

activate the OFF timer.

C) HOW TO SET A PROGRAM FOR

DAILY ON/OFF OPERATION (OR

VICEVERSA)

1. Set the timer ON/OFF as shown in A)

and B).

2. Press the ON/OFF button to start the

air conditioner.

3. Press three times the button to

activate the DAILY timer.

SETTING THE TIMER

After timer setting, press ST button in order to check the

ON/OFF setting time.

NOTE

TIMER SETTING PROCEDURE.

Press four times the button.The 1

HOUR TIMER mark will appear on the

display.

CANCELLATION PROCEDURE

Press the ON/OFF button to turn the air conditioner off.

Wait for the indoor unit to stop operating.

Press the ON/OFF button again to turn the air conditioner

on.

SETTING THE 1 HOUR TIMER

This function causes the unit to operate for one hour at the

set conditions, regardless of whether the unit is on or off.

SETTING THE HOLIDAY TIMER

The Holiday Timer function allows you to activate the

indoor unit (either it is the only one of a monosplit system

or one unit of a multisplit system), with a dalay up to

99 days you can set for the Daily Timer, On Timer, Off

Timer functions (not available for 1 HOUR TIMER) already

explained in this manual.

With this function you can set the air conditioner to be

switched on again after a long week end, a holiday of one

week or more, ecc…

To activate this function you have to follow the following

steps in order :

1. Keep pressed the button “TIMER SELECTION” of the

remote control unit (clock figure) for more than 6~7

seconds. In this way you enter the menu to select the

number of days of delay.

2. Select the desired timer (Daily Timer, On Timer,

Off Timer) pressing on the same button “TIMER

SELECTION”.

3. Set the desired number of days of delay using the

button “+” .

4. Keep pressed again the button “TIMER SELECTION”

for more than 6~7 seconds. You enter again the normal

menu of the remote control unit.

At this point, the symbol of the desired timer will flash

and the selected timer will be activated only after the set

number of delay days.

1 - 2 - 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo SDIAS8DC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo SDIAS8DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info