6
The air conditioner disposes of the condensate water automati-
cally at the HIGH and MEDIUM fan speed, on the contrary at
the LOW fan speed the condensate water is collected in the
tank.
1. Press the button SEL TYPE three times.
The time indication alone flashes.
2. Press the SET H button until the present time hour is
displayed.
Press the SET M button until the present time minu-
tes are displayed. The display will automatically stop
flashing.
HOW TO SET THE PRESENT TIME
COOLING
DEHUMIDIFYING (DRY)
The above mentioned data make reference to air conditioner
operating when the sensor on the remote control unit is ON.
(Refer to temperature sensor selector). If the sensor on the unit
is being used then actual operation will slightly differ from that
described in the above tables.
The automatic speed is not available in FAN ONLY mode.
ADJUSTING THE FAN SPEED
MANUAL
If you want to manually adjust speed just set the FAN selector
as desired.
NOTE
1 hour 1 hour TIME
Setting temperature
Room temperature
COOLING AND DEHUMIDIFYING
SLEEP MODE
●
The SLEEP mode enables you to save energy.
1.Set the MODE selector to cool or dry.
2.Press the NIGHT button.
3.The mark appears on the display. Press the NIGHT
button again to release the NIGHT function.
What does the SLEEP mode mean?
In this mode, the air conditioner will cool or dry the room to the
set temperature, and then the thermostat will make the unit
pause. After about 1 hour, the air conditioner will automatically
reset the set temperature as follows (also refer to graph).
When the room temperature reaches the new set value, the
thermostat will cause the unit to pause. After about 1 hour the
temperature will be raised by 1°C. This enables you to save
energy without sacrificing your comfort.
FAN ONLY
WHEN DIFFERENCE BETWEEN
ROOM TEMPERATURE AND SET FAN SPEED
TEMPERATURE IS
Cooling and
2 °C and over
High
dehumidifying
Between 2 and 1 °C
Medium
modes:
Below 1 °C
Low
EG
NOTE
THE DISPLAY SHOWS THE SELECTED
TEMPERATURE.
AFTER 5 SECONDS FROM THE REQUIRED TEM-
PERATURE SETTING THE DISPLAY WILL SHOW
THE ROOM TEMPERATURE AGAIN.
4. Press the FAN button to select the fan speed.
1
4
3
2
Verify that the unit is connected to the
main power and the STANDBY lamp is
light up.
1.Set the MODE selector to COOL .
2.Press the ON/OFF button and switch the
air condioner ON.
3.Press the TEMP. buttons to set the desi-
red temperature (the temperature range
is between 32 °C max. and 16 °C min.).
NOTE
1.
Set the MODE selector switch to “DRY” .
2. Press the ON/OFF button and switch the air condioner
ON.
3. Press the TEMP. buttons to set the desired temperature
(the temperature range is between 32 °C max. and 16 °C
min.).
THE DISPLAY SHOWS THE SELECTED
TEMPERATURE.
AFTER 5 SECONDS FROM THE REQUIRED TEM-
PERATURE SETTING THE DISPLAY WILL SHOW
THE ROOM TEMPERATURE AGAIN.
●
Use DRY operation when you want to reduce the humidity
in the room.
●
During DRY operation, the fan speed is automatically set to
or stops to prevent overcooling.
●
Dry operation is not possible if the indoor temperature
is 15 °C or less.
●
The humidity of the room (condensate water) will be collected
in the internal tank of the air conditioner.
NOTE
If you want to make air circulate without any temperature con-
trol, follow these steps:
1. Press the ON/OFF operation button and switch the air con-
ditioner ON.
2. Press MODE button until only the fan sign appears
on the display.
AUTOMATIC
Simply set the FAN selector to the position. A
microcomputer automatically controls the fan speed
when the AUTO mode is selected. When the air conditio-
ner starts operating, the difference between the room
temperature and the set temperature is detected by the
microcomputer which then automatically switches the fan
speed to the most suitable level.
High speed Med. speed Low speed
