Bedienungsanleitung Argo Wall Dual 18000 (Seite 10 von 30) (Englisch)

665465

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

V 11/15

7. SLEEP button

In cool, heat or dry mode, press this button to start the SLEEP function. The icon will appear

on the remote control display. Press the button again to exit the SLEEP function. The

icon will

disappear from the display.

8. TEMP button

Pressing this button will allow you to display the set temperature, the indoor ambient

temperature, or the outdoor ambient temperature on the indoor unit's display. You can cycle

through the settings on the remote control display as shown below:

nessuna

visualizzazione

nessunavisualizzazione no display

• When you select or “no display” with the remote control, the set temperature will appear

on the indoor unit's display.

• When you select

with the remote control, the indoor ambient temperature will appear on

the indoor unit's display.

• When you select

with the remote control, the outdoor ambient temperature will appear on

the indoor unit's display.

N.B.:

• It is not possible to display the outdoor ambient temperature on all models. The indoor unit

will receive the

signal but will display the set temperature.

• The set temperature will appear on the unit's display on start-up, if enabled to do so.

• When you select to display the indoor or outdoor ambient temperature, the indoor unit will

display the corresponding temperature for three to five seconds, after which it will

automatically revert to displaying the set temperature.

9. I FEEL button

Press this button to start the I FEEL function. The icon will appear on the remote control

display. When you select this function, the remote control will send the detected ambient

temperature to the indoor unit, which will then adjust its operation automatically based on the

difference between the detected temperature and the set temperature.

Press the button again to exit the I FEEL function. The

icon will disappear from the display.

The remote control should be positioned near the user when this function is selected. The

remote control should not be placed anywhere high or low temperatures may occur to

avoid inaccurate ambient temperature detection.

10. LIGHT button

Press this button to turn off the indoor unit's display light. The icon will disappear from the

remote control display.

Press this button again to turn on the display light. The

icon will appear on the display.

11. CLOCK button

Press this button to set the clock. The icon will flash on the remote control display. Press "▲"

or "▼" within 5 seconds to set the clock. Each time you press "▲" or "▼", the clock will increase

or decrease by 1 minute. Press and hold "▲" or "▼" for 2 seconds to rapidly change the time.

Release the button when you reach the desired time. Press "CLOCK" to confirm the time. The

icon will stop flashing.

N.B.:

• The time displays in the 24-hour clock format.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Wall Dual 18000 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Wall Dual 18000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info