Bedienungsanleitung Argon Radio 3i (Seite 21 von 27) (Englisch)

755604

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

www.argonaudio.com

R a d i o 3 i

7.4 Settings

Dynamic range compression

Some DAB broadcasts offer dynamic range compression (DRC). This feature allows radios to compress

the dynamic range of the output audio stream, so that the volume of quiet sounds is increased, and the

volume of loud sounds is reduced. This can be useful if you are listening to music with a high dynamic

range in a noisy environment (for example, classical music while cooking).

To change the DRC of the Radio3i, select Menu > DRC, and then DRC high, DRC low or DRC off.

Note: The Radio3i’s DRC setting does have any effect if DRC data is not included in the broadcast.

Station order

You can choose the order of the DAB station list to be either Alphanumeric, Ensemble or Valid. Ensemble

lists groups of stations that are broadcast together on the same ensemble, for example BBC or South

Wales local. Valid lists valid stations first, alphanumerically, then off-air stations.

To change station order, select Menu > Station order > then Alphanumeric, Ensemble or Valid.

8. FM radio mode

FM radio mode receives analogue radio from the FM band and

displays RDS (Radio Data System) information about the station

and show (where broadcast).

To enter FM mode, either press Mode until the display shows

FM Radio or select Menu > Main menu > FM.

8.1 Selecting stations

To find a station, press Select . The frequency display starts to run up as Radio3i scans the

FM band. Alternatively, you can scan up or down by pressing and holding the >> or << buttons

or tune manually with quick presses, or by turning the Select control.

Presets

To store an FM preset, press and hold Preset until the display shows the Save preset screen.

Select one of the 10 presets to save the currently playing station.

To select a preset, press Preset briefly, then select one of the listed preset stations. When a preset

station is playing, it shows Pn (P1, P2 etc) in the bottom right of the screen.

8.2 Now playing information

While an FM station is playing, the screen shows one of the two following sets data:

• If RDS information is available, by default the service name (i.e. station name) is displayed.

You can cycle through further RDS information by pressing Info . Each time you

press Info , another set of information is displayed, cycling through RDS radio text,

RDS programme type, frequency and today’s date.

• If no RDS information is available, the currently tuned frequency is shown.

8.3 Settings

Scan settings

By default, FM scans stop at any available station. This may result in a poor signal-to-noise ratio (hiss)

from weak stations. To change the scan settings to stop only at stations with good signal strength, select

Menu > Scan setting > Strong stations only? > Yes.

Audio settings

By default, all stereo stations are reproduced in stereo. For weak stations, this may result in a poor signal-

to-noise ratio (hiss). To play weak stations in mono, select Menu > Audio setting > FM weak reception:

Listen in mono only > Yes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argon Radio 3i Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argon Radio 3i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info