Bedienungsanleitung Ariston Blu Eco Evo (Seite 23 von 270) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

719606

Zoom out

Zoom in

Vorherige Seite

1/270

Nächste Seite

For models tted with a surge protection ange, remove the nut (D, g. 7) and remove the bracket xing the ange in

place (S, g. 7), then press the ange (F, g. 7) inwards and remove it with a semicircular movement.

For other models, loosen the 5 bolts (C, g. 8) and remove the ange (F, g. 8). The heating element and anode are

attached to the ange. During reassembly, make sure that the ange gasket, the thermostat and the heating element are

put back in their original positions (g. 7 and 8).

We recommend replacing the ange gasket (Z Fig. 9) every time it is disassembled.

Use only original spare parts.

Periodical maintenance

The heating element (R g. 9) should be descaled every two years to ensure it works properly approximately every two

years (the frequency must be increased, if water is very hard).

If you pre- fer not to use special liquids for this operation, simply crumble away the lime deposit without damaging the

heating element.

Replace the magnesium anode (N g. 9) every two years (except products with stainless steel tank),

but in the presence hard water or water rich with chloride it is necessary to verify the anode state every year.

To remove this, disassemble the heating element and unscrew from the support bracket.

Safety valve

Regularly check that the overpressure device is not jammed or damaged; if it is, remove any scale or replace it.

If the device has a lever or knob, operate it to:

- drain the appliance, if necessary

- check its operation from time to time.

USER INSTRUCTIONS

CAUTION Observe all general warnings and safety standards listed at the begin-

ning of this text in full; all such instructions are obligatory.

Advice for user

-Avoidpositioninganyobjectsand/orappliancesthatcouldbedamagedbywaterleaksbeneaththewaterheater.

- Should you not use any water for an extended period of time, you should:

➣ disconnect the appliance from the electrical supply by switching the external switch to “OFF”;

➣ turn off the plumbing circuit taps.

- Hot water at above 50°C owing out of the taps at the point of use could cause serious scalds or even death from burns.

Children, the disabled and the elderly are more exposed to the risk of burns. It is strictly forbidden for the user to perform

any routine or extraordinary maintenance.

Reset/Diagnostics

• For models featuring a user interface as represented in gures 3 and 4.

When one of the malfunctions described above occurs, the appliance will enter its “fault status” and all LEDs on the

control panel will ash simultaneously.

Reset: to reset the appliance, switch the product off and on again using the

button (Ref. A). If the cause of the mal-

function disappears immediately following the reset process, the appliance will resume normal operation. If this is not the

case,alltheLEDswillcontinuetoash;contacttheTechnicalAssistanceCentre.

Diagnostics: to enable the diagnostic function, hold the

button (ref. A) for 5 seconds. The type of fault is indicated by

ve LEDs (Ref. 1-5) according to the following scheme:

LED ref. 1 – Internal P.C.B. malfunction;

LEDref.2–Anodemalfunction(inmodelsttedwithactiveanode);

LED ref. 3 – NTC 1/NTC 2 temperature sensors broken (open or short-circuited);

LED ref. 5 – Water overheating detected by an individual sensor;

LEDs ref. 4 and 5 – General overheating (P.C.B. malfunction);

LEDs ref. 3 and 5 – Sensor differential error;

LEDs ref. 3, 4 and 5 – Operation without water.

Exit the diagnostic function by pressing the

button (Ref. A) or wait for 25 seconds.

• For models featuring a user interface as represented in gures 5 and 6.

When any of the operation problems occur, the appliance goes into “fault status” and the corresponding error code

ashes on the display (for example, E01). The error codes are the following:

E01 – E02 – E03 – Water overheating;

E10 – E11 – E12 – E13 – E16 – NTC sensor error (sensor malfunction);

E04 – Operation without water;

E14–E15–Anodeerror;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston Blu Eco Evo Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info