Bedienungsanleitung Ariston Blu Eco Evo (Seite 24 von 270) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

719606

Zoom out

Zoom in

Vorherige Seite

1/270

Nächste Seite

E50 – E51 – Maintenance request;

E60 – E90 – E91 – E92 – P.C.B. software error.

Reset: to reset the appliance, switch the product off and on again using the

button (Ref. A). If the cause of the mal-

function disappears immediately following the reset process, the appliance will resume normal operation. If this is not the

case,theerrorcodewillcontinuetoappearonthedisplay;contacttheTechnicalAssistanceCentre.

Activating the “thermal disinfection cycle” (anti-legionella)

The product has the "thermal disinfection cycle" disabled by default.

The activation of the "thermal disinfection cycle" is displayed as a normal temperature setting at 70°C.

For models featuring a user interface as represented in gures 3 and 4:

Activatethisfunctionbypressingandholdingboththe"ECO"and"+"keysfor4s.;onceactivationisconrmed,LED

70 will ash quickly for 4 s.

Permanently deactivate the function by repeating the above steps; once the deactivation is conrmed, LED 40 will ash

quickly for 4 s.

For models featuring a user interface as represented in gures 5 and 6:

Duringtheanti-bacteriacycle,thedisplayalternatesbetweenthetemperatureofthewaterandthetext“-Ab-”.

To disable/enable the function, while the product is in operation, press and hold the “mode” button for 3 seconds. Select

“Ab0”(todisablethefunction)or“Ab1”(toenablethefunction)usingthe“set”knob,thenconrmbypressingtheknob.

Afterconrmingthatthefunctionhasbeendisabled/enabledsuccessfully,theproductwillreverttoitsnormaloperating

status.

Whentheproductisswitchedoff,theAnti-Legionnaire'sdiseasefunctionisnotactive.Intheeventthatthedeviceis

switchedoffduringtheAnti-Legionnaire'sdiseasecycle,theproductisswitchedoffandthefunctionisnotcompleted.At

the end of each cycle, the operating temperature returns to that set previously by the user.

Setting/adjusting the local time

(For models featuring a user interface as represented in gures 5 and 6)

To adjust the local time, the rst time the product is switched on it will automatically prompt you to set the correct time;

onsubsequentoccasionsyouwillneedtopressandholdthe"set"knobfor2seconds.Adjustthecurrenthoursetting

by turning the “set” knob, then conrm the value by pressing the knob. Repeat the procedure to set the minute value.

Adjusting the temperature and activating the functions

• For models featuring a user interface as represented in gures 3 and 4:

Press the

button (Ref. A) to switch on the appliance. Set the desired temperature by using the “+” and “-” buttons to

select a level between 40°C and 80°C. During the heating phase, the LEDs (Ref. 1➔5) corresponding to the tempe-

rature reached by the water so far remain lit in a xed manner; all subsequent LEDs (up to the set temperature) ash

progressively.

If the temperature drops, for example after hot water has been used, the heating is reactivated automatically and the

LEDs between the last xed light and the light corresponding to the set temperature will resume ashing progressively.

The rst time the product is switched on, it will be set to a temperature of 70°C.

In the event of a power failure or if the product is switched off using the

button (Ref. A), the most recently set tempe-

rature remains memorised. During the heating phase, a slight noise may be produced as a result of the water heating

process.

• For models featuring a user interface as represented in gures 5 and 6:

Press the button (Ref. A) to switch on the appliance. The product has 4 operating modes: Manual, Programming 1,

Programming 2 and Programming 1and2. Every time the “mode” button is pressed, a different operating mode will be

selected (the mode is indicated by the ashing of the corresponding LED near the display). Functions are selected on a

cyclic basis, in the following order: “P1”➔“P2” ➔“P1andP2”➔“Manual” ➔ “P1”, etc.

Programmes “P1” and “P2” are set by default to the 07:00 and 19:00 time bands, and to a temperature of 70°C.

The “Manual” function (“Manual” LED lit) allows the user to set the desired temperature simply by turning the “set” knob

until the selected temperature is displayed (the adjustment interval is 40°C - 80°C). If the knob is pressed, the setting will

be stored in the appliance memory and the product will begin operating in “Manual” mode.

ECO EVO: If the “Manual” function is used in conjunction with the “ECO EVO” function (see “ECO EVO function” para-

graph), the temperature will be set automatically by the product; this means the "set" knob will be disabled. If it is moved,

“ECO” will appear on the display for 3 seconds. If you wish to adjust the temperature, you will have to disable the “ECO

EVO” function.

The functions “Programming 1” (“P1” LED lit), “Programming 2” (“P2” LED lit) and “Programming 1and2” (“P1andP2”

LEDs lit) can be used to programme 1 or 2 time bands in the day during which hot water is required. Press the “mode”

button until the LEDs relating to the desired programme begin ashing.

Atthispoint,turnthe“set”knobtoselectthetimebandinwhichyouwouldlikehotwatertobeavailable(timebands

are selected in 30-minute notches). Press the knob to store the time band setting in the appliance memory. Next, set the

water temperature to the desired level (the adjustment interval is 40°C-80°C). Press the “set” knob to begin appliance

operation in “P1” or “P2” mode. If you have selected “P1andP2”, you will need to repeat the time band and temperature

setting procedures for the second time period. During the periods for which the use of hot water has not been scheduled,

Ariston Blu Eco Evo Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info