Bedienungsanleitung Ariston CP 65S F8 (Seite 17 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch)

591457

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

HOOD

900

Min. mm.

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

420

Min. mm.

Fig. C Fig. D

Gas connecting

The appliance should be connected to the gas mains or to

a gas cylinder in compliance with current Norms in force.

Before making the connection, check that the cooker is

regulated for the gas supply you are using. If not, follow

the instructions indicated in the paragraph “Adapting to

different types of gas.” On some models the gas supply

can be connected on the left or on the right, as necessary;

to change the connection, reverse the position of the hose

holder with that of the cap and replace the gasket (sup-

plied with the appliance). When using liquid gas from a

cylinder, install a pressure regulator which complies with

current Norms in force.

Important: Check that the supply pressure complies with

the values indicated in table 1 “Burner and Nozzle Charac-

teristics” since this will ensure safe operation, correct con-

sumption and ensure a longer life to your appliance.

Connection with hose

Make the connection using a gas hose that complies with

requirements set forth by the current standards. The inner

diameters of the pipe are as follows:

- 8 mm for liquid gas;

-13mm for methane gas;

When installing the hose, remember to take the following

precautions:

• No part of the hose should touch parts whose tem-

perature exceeds 50°C;

• The length of the hose should be less than 1500 mm;

• The hose should not be subject to twisting or pulling,

and should not have bends or kinks.

• The hose should not touch objects with sharp edges,

moving parts, and it should not be crushed;

• The full length of the hose should be easy to inspect in

order to check its condition;

Check that the hose fits firmly into place at the two ends

and fix it with clamps complying with current standards. If

any of the above recommendations can not be followed,

flexible metal pipes should be used.

If the cooker is installed according to the conditions of

Class 2, subdivision 1, only a flexible metal pipe which is

in compliance with current safety standards should be used

to make the connection to the gas mains.

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Remove the hose holder fitted on the appliance. The gas

supply pipe fitting is a threaded 1/2 gas cylindrical male

attachment. Only use pipes and gaskets complying with

current standards. The full length of the pipe must not ex-

ceed 2000 mm.

Checking that the connection is tight

Important: When installation has been completed, check

the pipe fittings for leaks using a soapy solution. Never

use a flame.

Once the connection has been made, ensure that the flex-

ible metal pipe does not touch any moving parts and is

not crushed.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indi-

cated on the data plate. When connecting the cable di-

rectly to the mains, install an omnipolar circuit-breaker with

a minimum contact opening of 3 mm between the appli-

ance and the mains. The omnipolar circuit breaker should

be sized according to the load and should comply with

current regulations (the earth wire should not be interrupted

by the circuit breaker). The supply cable must be in such a

position that no part of it can reach a temperature of 50°C

above room temperature. Before connecting to the power

supply, make sure that:

• the limiter valve and the domestic system can with-

stand the load from the appliance (see rating plate);

• the mains are properly earthed in compliance with cur-

rent directives and regulations;

• there is easy access to the socket and omnipolar cir-

cuit breaker, once the hob has been installed.

N.B.:never use reducers, adapters or shunts since they

can cause heating or burning.

Adapting the cooker to different types of gas

In order to adapt the cooker to a different type of gas with

respect to the gas for which it was manufactured (indi-

cated on the label attached to the back of the appliance

and to the packaging), follow these steps:

a) replace the hose holder mounted on the appliance with

that supplied in the bag of “cooker accessories”.

Warning: The hose holder for liquid gas is marked 8, the

hose holder for methane gas is marked 13. Always fit a

new sealing gasket.

b) Replacing the burner nozzles on the hob:

• remove the grids and slide the burners from their

housings;

• unscrew the nozzles using a 7 mm socket spanner,

and replace them with nozzles for the new type of gas

(see table 1 “Burner and nozzle characteristics”).

• Replace all the parts, following the steps described

above in the reverse order.

Instructions for installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston CP 65S F8 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info