Bedienungsanleitung Ariston NUOS 200 SPLIT (Seite 42 von 104) (Englisch, Holländisch, Französisch, Italienisch)

566471

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Heat pump water heater – OPERATING AND MAINTENANCE INSTRUCTIONS

7.3 Setting the temperature

The desired temperature for the hot water can be set by turning the knob clockwise or anti-clockwise (the 42isualize42

temperature will flash temporarily).

To 42isualize the current temperature of the water in the tank, press and release the knob; the relative value will

appear for 8 seconds then the set temperature will reappear once again.

The temperatures that can be obtained in the heat pump mode vary between 50 °C and 55 °C, by factory default

setting. By accessing the installer menu (illustrated in Paragraph 7.7), the interval range can be extended to between

40 °C and 62 °C (bear in mind that temperatures exceeding 55 °C in the heat pump mode may lead to greater wear

of the compressor).

The maximum temperature that can be obtained with the heating element is 65 °C, by factory default setting, and

75 °C, by varying the setting on the installer menu.

7.4 Mode of operation

In normal operating conditions, the “mode” button can be used to vary the operating

mode through which the water heater reaches the set temperature. The selected

mode will be 42isualize42 on the line below the temperature.

If the heat pump is active, the following symbol will appear:

If the heating element is active, the following symbol will appear:

• AUTO: the water heater understands how to reach the desired temperature in a few hours, through the rational

use of the heat pump and, only if necessary, of the heating element. The maximum number of hours it takes

depends on the P9 – TIME_W parameter (see Paragraph 7.7), which is set to 8 hours by default.

(recommended for winter to ensure the better comfort).

• BOOST: by activating this mode, the water heater simultaneously uses the heat pump and heating element to

reach the desired temperature in the shortest possible time. Once this temperature is reached, the AUTO

operating mode is restored.

• BOOST 2 (to be activated through the installer menu): Compared to Boost, the Boost2 mode remains active

even after the set temperature is reached.

• GREEN: the water heater will use the heat pump, thereby ensuring maximum energy saving! The maximum

temperature that can be reached depends on the value of the P3 parameter (51 °C-62 °C) – refer to Paragraph

7.7. The heating element may turn on only in the event that occurs inhibition of operation of the heat pump

(errors, air temperature out of operating range, defrosting process in progress, anti-legionnaire’s disease). This

function is recommended for air temperatures above 0 °C during the hours of heating.

• PROGRAM (to be activated through the installer menu): You have two programs P1 and P2, which may act

either individually or in combination with each other during the day (P1 + P2). The device will be able to activate

the heating phase to reach the selected temperature set in the timetable, giving priority to heating by heat pump

and, if necessary, through the heating elements.

Press the mode button to select the desired Program mode, turn the knob to set the desired temperature, press

it again to confirm, turn the knob to set the desired time and press to confirm; mode P1 + P2 can set the

information for both programs. In the case of electrical connection with two-tier price signal HC / HP, you still

possible program the water heater at any time of day. For this function is required the setting of the current time,

see the next paragraph.

Note: To ensure comfort, in the case of P1 + P2 mode operation with very close times between them, it is

possible that the temperature of water is higher than the temperature set, in which case it may appear the

symbol of the waves.

• VOYAGE (to be activated through the installer menu): studied for situations in which users are absent from

the appliance’s operating location; this mode allows for programming the number of days of absence, during

which the water heater will remain turned off. The appliance will activate only to supply hot water on the day of

arrival; protection against corrosion will continue to be guaranteed while the product will automatically ensure

that the temperature of the water in the tank does not fall below 5 °C. Press the “mode” button until selecting

the VOYAGE mode, turn the knob to set the number of days (“days”) then press the knob to confirm. The

display will only 42isualize the number of days that remain until the product’s reactivation.

In the event of an

electric connection with a day/night contactor or with HC-HP signal, the number of nights of absence must be

specified, taking into account that the product only operates during the night.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston NUOS 200 SPLIT Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info