Bedienungsanleitung Ariston NUOS 200 SPLIT (Seite 44 von 104) (Englisch, Holländisch, Französisch, Italienisch)

566471

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Heat pump water heater – OPERATING AND MAINTENANCE INSTRUCTIONS

7.7 Installer menu

CAUTION: THE FOLLOWING PARAMETERS MUST BE ADJUSTED BY QUALIFIED PERSONNEL.

Several of the appliance’s settings can be modified through the installer menu. The maintenance

symbol is 44isualize44 on the left.

To enter the menu, keep the knob pressed for 5 seconds then scroll the parameters of the “L

– INFO” menu until reaching “PO – CODE”.

After entering the code (illustrated in the table that follows), turn the knob to select the parameters

P1, P2, P3 … C2.

Upon reaching the parameter to be modified, press the knob to

isualize

the parameter’s value

then turn the knob to set the desired value.

To return to the parameter selection area, press the knob to store the entered parameter or press

“mode” (or wait 10 seconds) to exit without storing the entered value.

To exit the installer menu, press the “mode” button (the appliance will ensure that the menu

is automatically exited after the latter has been idle for 10 minutes).

Parameter

Name

Parameter d

escription

P0 CODE

Code entering to access the installer menu. The number 222 appears on the display: turn the

knob until reaching number 234 then press the knob. It will then be possible to access the

installer menu.

T Max

Adjustment of the maximum o

btainable temperature (from 65

°C to 75

°C).

A higher temperature value allows for using a greater amount of hot water.

P2 T Min

Adjustment of the minimum obtainable temperature (from 50 °C to 40 °C).

A lower temperature setting allows for more energy-efficient operation in the event of limited

hot water consumption.

P3 T HP

Adjustment of the maximum temperature obtainable with the heat pump unit (from 50

°C to 62

°C). Bear in mind that operating at temperatures above 55 °C with the heat pump may lead to

greater wear of the compressor.

P4 GREEN

Activation/deactivation of the Green function (on/off).

See Paragraph 7.4.

P5 ANTI_B

Acti

vation/deactivation of the

anti

legionnaire’s disease function (on/off).

See Paragraph 7.9.

P6 VOYAGE

Activation/deactiva

tion of the Voyage function (on/off).

See Paragraph 7.4.

P7 DEFROS

Activation/deactivation of the defrost mode (on/off).

If activated, this mode allows the heat pump to function at air temperatures as low as -5 °C.

P8 HC-HP

Activation/deactivation of th

e two

tier rate operation mode

with HC HP signal (Warning: activate

it only if signal cable HC-HP is connected). See Paragraph 7.11.

TIME_W

Maximum number of hours of daily heating (from 5h to 24h).

P10

RESET

Resetting of all factory default settings.

P11

PROG

Activation/deactivation of the

Program function

: P1, P2, P1+P2 (on/off).

BOOST2

Activation/deactivation of the Boost2 function (on/off).

C1 CHECK

Activation

of the

electric connection check (activate this only in presence of mains alimenta

tion

and air temperature below 30 °C).

C2 CHARGE

Activation of the cycle inversion procedure, to allow the gas charging (see paragraph 4.9)

(activate this only in presence of mains alimentation).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston NUOS 200 SPLIT Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info