Bedienungsanleitung Ariston XF 905 (Seite 14 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

455107

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

It is a good idea to do the following:

- Only use the appliance to cook food, nothing else;

- Check the soundness of the appliance after it has been

unpacked;

- disconnect the appliance from the electrical mains if it

is not functioning properly and before cleaning or

performing maintenance;

- When the appliance is not used for an extended period

of time, cut off the supply of power and close the gas

cock (if present);

- Use cooking gloves to place cookware in the oven or

when removing it;

- Always grasp the oven door in the centre because the

ends may be hot due to the escape of hot air;

- Make sure that the control knobs are on the “•”/”o”

setting when the appliance is not in use;

- Cut the power supply chord after disconnecting it from

the mains when you decide not to use the appliance

any longer.

Installation

Important: The power supply to the appliance must be

cut off before any adjustments or maintenance work is

done on it.

Installation of Built-in Ovens

To ensure the proper working order of the built-in

appliance, the kitchen unit must be of a suitable size.

The sizes of the unit for installing the cooker under a

worktop or in a column unit are shown in figure.

To provide adequate ventilation, there must be appropriate

ventilation openings in the front bottom and the top part of

the cabinet (an intake opening on the bottom of at least

200 cm

, and an exhaust opening of at least 60 cm

The unit panels next to the cooker must be heat resistant.

In the case of veneered wood units, glues must be resistant

to a temperature of 120 °C.

In accordance with safety standards, once the appliance

has been mounted, there must be no possible contact

with electrical parts. Any protective parts must be secured

so that they can only be removed with the use of tools.

Fastening the oven

The oven must be fastened to the cabinet using the 4

holes (A) located on the frame (see Fig. 12).

Use the 4 self-tapping wood screws.

Bear in mind that you can access the two "A" holes on the

left side by simply opening the oven door.

To access the two "A" holes on the right side, proceed as

follows:

- remove the knobs (pull them towards the front);

- with the door open, completely remove the "B" screw;

- loosen the two "C" screws (this will allow the control

panel to slide vertically);

- at this point, lower or raise the control panel to gain

access to the two "A" holes on the right and screw in

the two screws;

- replace the "B" screw removed earlier and tighten the

two "C" screws;

- remount the knobs.

447 mm

min. 550 mm

3 mm

472 mm

480 mm

860 mm

22 mm

895 mm

525 mm

469 mm

840 mm

min. 45 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston XF 905 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ariston XF 905

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info