Bedienungsanleitung Aritech ATS1203 (Seite 5 von 24) (Englisch, Französisch, Italienisch)

702276

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Only use units in a clean environment and not in humid air.

5. Installation of ATS1203/ATS1204

(Ref. to figure )

(1) Earth connection. Use also for cable screen and lid

of box.

(2) Processor

(3) Mains power connection

(4) Back-up battery

(5) Pry-off tamper mounting location

To conform with CEI 79-2 regulations at level 2, the

use of the pry-off tamper is mandatory (ST580 or

ST590 kit). Note: The pry-off tamper is not included

with the product.

For detailed information on the PCB, see connection

diagram.

6. Cabling ATS1203/ATS1204 with

control panel ATS2/3/4/4500

(Preferred System databus wiring – refer to figure )

(Refer to the ATS Control Panel installation guide for a

more detailed description of the cabling)

The “TERM” link is on the first and last devices on the

system databus. In a “star” wiring configuration, the

“TERM” link is only fitted on the devices at the ends of the

two longest system databus cable runs.

(1) TERM link fitted (first device on local databus)

(2) Control Panel ATS20/26/30/36/40/45/4600

(3) ATS1105 LCD RAS (TERM switch not set to ON)

(4) Separate 12 V power supply. (Required if RAS is

more than 100 m from the nearest panel or DGP.

Connect “-“ to “-“ of the databus.)

(5) Preferred data cable type is WCAT 52 (2 pair

twisted).

(6) TERM link fitted (last device on local databus)

(7) Earth connection to connect shield*

(8) Any data gathering panel like ATS1201, ATS1203,

ATS1210, ATS1220 or ATS1250.

*Connect cable shield to one device only.

See: System databus connection and Earthing details on

page 5 and 6.

7. Connection diagram

ATS1203/ATS1204 (ref. to figure )

(1) AC connection from transformer

(2) System earth (see details page 6)

(3) 12 V battery

(4) Earth connection for cable screens (shields)

(5) Auxiliary power supply output

(6) System databus

(7) Normally closed panel tamper contact

(8) Normally closed panel tamper contact

(9) Normally closed Alarm Contact

(10) Normally Closed Tamper Contact

(11) Interface to ATS1202 input expanders

(12) External 8 Ohm siren speaker or siren

(13) 1K resistor must be fitted if external siren not

connected

(14) Clock-out Interface to plug on output expansion or

4-way non-clocked output expansion (e.g.

ATS1810).

(15) Dipswitch to set DGP Address

(16) Link to select +12Vdc to output board

(17) Link to terminate databus

J1 RS485 system databus & box tamper

connections.

J5/J6 Zones

J7 Interface to ATS1202 input expanders

J8 Clock-out Interface to plug on output

expansion or 4-way non-clocked output

expansion (e.g. ATS1810).

J13 External siren

J14 Auxiliary power output.

J17 AC connection from transformer and battery

power

8. Important notes

1. If the battery load resistor is enabled, the 8

output

is no longer available for non-clocked output

expansion boards.

2. In case the DGP is set for 2 DGP’s to enable all 32

outputs, the control panel programming should be

set up to poll the DGP address and the address + 1.

9. Links

TERM Termination of databus. Only to be used on

first and last device on the local databus.

+12V Connect +12VDC to output board

10. DGP dipswitch settings (ref. to

figure )

Address Select DGP address. Set switches 1 - 4 to

OFF to disable the DGP. (See fig. 2 for

correct address settings.)

11. LEDs

Tx Red LED flashes when remote units (RAS

and DGP) are replying to polling.

Rx Yellow LED flashes when panel is polling

remote unit(s). It must always be active.

12. System databus connection

The system databus is used to connect Data Gathering

Panels (to provide extra zones) and Arming Stations to the

ATS control panel. Remote devices can be up to 1.5 km

from an ATS control panel.

Arming stations and Data Gathering Panels must be

connected via a 2 pair twisted shielded data cable from the

system databus connection. (WCAT 52 is recommended)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1203 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info