Bedienungsanleitung Aritech ATS1203 (Seite 6 von 24) (Englisch, Französisch, Italienisch)

702276

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

The shield of the data cable should be connected to earth

at the ATS control panel or any other earth point. However

it should be left disconnected at the other end.

It is recommended that where the distance between the

arming station and the nearest device is more than 100

meters, a separate power supply be used to power the

arming station.

To power the arming station, do not connect ‘+’ from the

system databus. Connect '+' of the local power supply to '+'

on the arming station and connect 0 volts from the power

supply and 0 volts from the system databus to the arming

station terminal marked ‘-’.

See also Cabling ATS1203/ATS1204 on page 5.

13. Mains connection

Make sure that before connecting the mains power to the

control panel, the mains power supply is disconnected

using a circuit breaker or by removing the AC from the wall

socket. (see page 4).

When installing the mains power, use a strain relief like

cable ties and coupling PG16’s to ensure proper wiring. In

all cases, local regulations should be applied.

14. Earthing (ref. to figure )

WARNING!

Correct Earthing procedures must be

followed

 Earthing of one cabinet containing several

devices.

All devices designed for the system have earth connections

via metal studs to the metal housing. Take care, that these

metal studs make good connection to the housing (beware

of paint).

The earth connections of every piece of equipment in the

system, can be used for connecting the shielding of

shielded cables. However: never connect the shield at both

sides to earth. If a device is placed in a plastic housing the

earth lug of this device does not have to be connected.

 Earthing panels in a single building.

In one building several cabinets or devices are earthen to

safety ground.

The safety earth of this building has to be checked by a

licensed contractor.

 Earthing panels in more buildings.

If the wiring extends to separated buildings, more than one

common earth system will be used. Use isolator/repeaters

ATS1740 to isolate the system databus. In this way the

system is protected against variations in earth potential.

 Shielding

The shielding of all shielded cables used in the system,

should only be connected at ONE side to one common

earthing point in a building (see Fig. 3) If a shielded

databus cable is routed via more than one plastic device

the shielding from incoming and out-going cable has to be

connected.

 Explanation of fig.



(1) Mains power with local earth

(2) Mains power connector

(3) System databus

(4) Earth lug

(5) Building 1

(6) Building 2

(7) Device in metal housing

(8) Device in plastic housing

(9) ATS20/26/30/36/40/45/4600 control panel

15. Connecting the data gathering panel

to a control panel

Refer to the control panel installation guide for instructions.

16. Zone and output numbering

Control panel 1 - 16 DGP8 129 - 144

DGP1 17 - 32 DGP9 145 - 160

DGP2 33 - 48 DGP10 161 - 176

DGP3 49 - 64 DGP11 177 - 192

DGP4 65 - 80 DGP12 193 - 208

DGP5 81 - 96 DGP13 209 - 224

DGP6 97 - 112 DGP14 225 - 240

DGP7 113 - 128 DGP15 241 - 256

Output numbering

A DGP can have a maximum of 16 outputs available as

relays or open collectors outputs. The output numbers are

the same as the 16 zone numbers allocated to the DGP

address.

The ATS1203/ATS1204 can also support 32 outputs.

Enable this by selecting “2 DGP addresses” in menu 3-

“DGP settings” (first option). Be aware that the ATS Control

Panel needs to be setup to poll both DGP addresses.

Note: If the Battery Load test resistor is enabled, the 8

output follows the battery test (except when using clocked

output devices).

Zone numbering

The ATS1203/ATS1204 has 8 zones that can be expanded

using the ATS 1202 (8 zones) to a maximum of 32 zones.

If the number of zones exceeds 16, then the zones are

taken from the next DGP address and DGP ceases to

exist.

e.g. DGP 1 has 24 zones (zones 17 to 40). The next

DGP in the system must now be addressed and polled as

DGP 3, because zones 33 to 40 on DGP 1 have been

taken from DGP 2.

The unused zone numbers in the system (zones 41 to 48)

must be programmed in the zone database as Type 0.

17. Programming (ref. to figure )

The ATS1203/ATS1204 provides a menu through which a

number of options can be set. In addition the status of the

ATS1203/ATS1204 itself or inputs can be viewed.

To enter the programming menu for the

ATS1203/ATS1204:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1203 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info