Bedienungsanleitung Aritech ATS1234 (Seite 5 von 36) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Finnisch)

702278

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ATS123

Wireless DGP on 868 MHz FM

Introduction

The ATS1234 Wireless Data Gathering Panel (DGP) receiver expands

the ATS control panel’s input capability by up to 32 zones using the

Learn Mode ™ 868 MHz FM Wireless Transmitter Sensors (crystal or

SAW).

The ATS1234 requires an ATS control panel firmware version

04.05.10 or later. Full compliance and functionality of ATS1234 is

only provided from panel firmware version 04.08.xx or later.

It has a new concept of mother- and daughterboard. In the future

this concept will allow different frequencies by replacing only the

motherboard.

• Up to 15 DGPs can be connected to the ATS control panel

providing 240 wireless zones (also known as inputs), or up to

240 fobs to arm/disarm area or activate/deactivate relay

controls.

• The maximum recommended data bus length is 1500 m

when one or more ATS1234 Wireless DGP is connected.

• The Wireless DGP features spatial diversity to minimise

wireless signal nulls or dead spots and has a nominal open-

air receiving range of 400 m.

• If dead spots need to be eliminated, a 868 MHz FM repeater

may be used.

• The Wireless DGP may be powered from the ATS control

panel data bus or a remote auxiliary power supply.

• Fob buttons may be programmed for users to arm and

disarm or to control relays, for example, to remotely open

and close a garage door as well as arm or disarm a security

system.

Description of the ATS1234

n Motherboard

SW2 Cover tamper

SW3 Reed Switch

J1 Terminal strip

J3 Connector to daughterboard

Led 4 RF/Power LED

Led 3 Bus LED, Flashing LED indicates communication

between motherboard and daughterboard is present.

o Daughterboard

J1 Connector to motherboard

Led1 Tx LED. The red Tx led flashes to indicate the DGP is

replying to the polling from the control panel

Led 2 Rx LED. The yellow led indicates polling data is being

received from the panel

JP1 Bus 470 ohm EOL

Basic system layout

The ATS control panel collects the data from the wireless DGP on the

data bus. It provides the power supply to the DGP or a remote 220 V

powered DGP can supply power to the ATS1234.

The ATS1234 receives the RF signal from the wireless devices, such

as PIR, FOB or smoke detectors.

A programmable supervisory signal checks the state of the

devices in the field. Transmitters send one supervisory signal every

15 minutes. For more details of the supervision functionality, refer to

menus 8, 9 and 10.

Mounting location (see fig.p)

The ATS1234 can be mounted on any interior wall.

Leave 16 cm above the wireless DGP plastic enclosure for the

antenna.

 1. Avoid areas likely to expose the wireless DGP to moisture.

2. Avoid excessive metal or electrical wiring, e.g. furnace &

utility rooms.

3. If mounting wireless DGP near metal, give the antenna as

much clearance as possible.

Mounting the unit

Mounting the ATS1234 DGP

1. Remove power from the ATS control panel before

commencing installation.

2. Remove the ATS1234 plastic cover.

3. Hold the base of the ATS1234 against the mounting surface

and mark the two mounting holes (leave 18 cm of free

space above for the antenna).

4. Drill holes and insert screw anchors, if required.

5. Secure the unit to the mounting surface with screws

provided. If mounted near metal, give the antenna as much

clearance as possible.

6. The bottom mounting hole screw automatically will secure

the pry off tamper switch tab.

 Remember to enable the back tamper in the ATS1234 menu 12

- Tamper Options when required by local regulations.

7. Place the daughterboard with connector J1 onto J3 of the

motherboard.

8. Stretch the antenna wire loop, assemble the plastic cover

and clip them over the antenna loops.

Connecting the ATS1234 (see fig. n)

1. Connect the four bus cable wires to the terminal strip J1 on

the DGP.

• +12

• A = D+

• B = D -

• GND

2. Connect the bus cable directly to the ATS control panel bus

and auxiliary power or use a separate power cable to the

nearest 220 V-powered DGP (in that case, 0 V needs to be

connected to the panel and the DGP as well).

The ATS1234 may be located up to 1500 m from the ATS control

panel using a WCAT52/54 cable (see example below.) This cable has

a core with a gauge of AWG24, the diameter is 0.52 mm and the

area is 0.22 mm².

 JP1 (terminator) can be placed on the last device on the

bus.

Wiring specifications

Wire gauge / diameter (shielded) Max. wire length between

module and panel

AWG Diameter Area Meters

24 0.52 mm 0.22 mm² 1500

Addressing ATS1234 (see fig.q)

Each Wireless DGP, connected to the ATS control panel bus must

identify itself to the ATS control panel with its own address, set with

the DIP switches on the DGP. Figure

q shows 2 possible settings of

the DIP switch, and the table shows the 15 possible Wireless DGP

addresses.

 Address 0 is a factory test setting — do not use it!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1234 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info