Bedienungsanleitung Aritech ATS1234 (Seite 6 von 36) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Finnisch)

702278

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Closing ATS1234 Wireless DGP housing

1. Replace the plastic cover. Make sure the cover tamper

switch extension spring is in place on the tamper switch.

2. Mount sensors and 868 MHz FM repeater (a repeater can be

added later if sensor performance or signal strength is

found to be inadequate).

Powering up the ATS1234 Wireless DGP

Before powering up the panel and receiver module:

1. Verify that all wiring at the panel and ATS1234 wireless

receiver is correct.

2. Connect the panel backup battery and AC power.

Verify that the RF/Power LED is on. For troubleshooting refer to the

chapter Testing and Installation Troubleshooting.

Output numbering

The output numbering of a Wireless DGP is in line with all DGPs

(please refer to Table 1), but the Wireless DGP has no physical

outputs or output expansion available. However, any available

output can be programmed in the range of 1 – 255 via key fob

programming in menu 6.

 Remember that in standard DGP mode the first relay of each

DGP (relay 17 for DGP 1) can be used to mask supervision on

sensors by using time zones to energise/de-energise the virtual

relay (see Menu option 11 – Supervision Options).

Table 1. Output numbering.

Control panel 1 - 16 DGP 8 129 - 144

DGP 1 17 - 32 DGP 9 145 - 160

DGP 2 33 - 48 DGP 10 161 - 176

DGP 3 49 - 64 DGP 11 177 - 192

DGP 4 65 - 80 DGP 12 193 - 208

DGP 5 81 - 96 DGP 13 209 - 224

DGP 6 97 - 112 DGP 14 225 - 240

DGP 7 113 - 128 DGP 15 241 - 255

Zone numbering

The Wireless DGP zone database can be set up as either a 16-zone

or 32-zone database. This means you can add up to 16 or up to 32

wireless devices to the DGP. If the DGP 1 is been programmed with

32 zones, then the next 16 zones (33-48) normally belonging to DGP

2 will now belong to DGP 1 and the RAS display would show 17-48

(for more details, refer to Table 2 and Menu 14, DGP settings).

Table 2. Zone numbering.

Control panel 1 - 16 DGP 8 129 - 144

DGP 1 17 - 32 DGP 9 145 - 160

DGP 2 33 - 48 DGP 10 161 - 176

DGP 3 49 - 64 DGP 11 177 - 192

DGP 4 65 - 80 DGP 12 193 - 208

DGP 5 81 - 96 DGP 13 209 - 224

DGP 6 97 - 112 DGP 14 225 - 240

DGP 7 113 - 128 DGP 15 241 - 256

Introduction to the programming (see fig.r)

Each sensor must be programmed into the Wireless DGP database

via an ATS control panel RAS keypad. In this procedure it is

assumed that:

• Sensor / key fob documentation is available or known.

• The DIP switch address for the Wireless DGP is set correctly.

• The DGPs database size has been correctly selected. The

factory default sets the DGP to 16 detectors.

 If planned to have 32 detectors on the DGP, you first need to

change the option in menu 6 from 16 to 32 before learning any

sensor!

• Sensors are physically installed or mounted.

• The repeater has been installed and programmed if

required.

The specific details per sensor need to be reviewed in the related

component sheet. In general, you need to know that the sensor can

be learned into the system by creating a tamper on the detectors

and door window sensors and for key fobs that you need to press

the matching two buttons at the same time during the auto learning

when in the proper menu (see further on for details).

Programming (see fig.r)

Selecting the Remote Wireless DGP Menu (Panel menu)

The ATS1234 provides a menu through which a number of options

can be set. This menu is an internal DGP menu (see the menu tree

on figure

r). In addition the status of the ATS1234 itself or inputs

can be viewed.

To enter the programming menu for the ATS1234:

1. Enter menu 28 of the Control Panel installer menu.

2. Press 1 [ENTER] followed by the DGP address selected and

[ENTER] to enter the DGP menu. The display now shows

"ATS1234" followed by the version number.

3. Press [ENTER] to proceed to the menu or press the menu

number followed by [ENTER] to go to a menu item directly.

Programming a sensor with single zone

 The menu has a generic approach for future sensors. At the

moment 868 FM does not have devices with more than one

zone, please select 1!

Zone numbering and sensors

The input numbers used are related to the address selected (see

Zone numbering on page 6).

To view the status, enter the first input to view. The selected input

status is shown. Press [*MENU] to view the previous or [ENTER] to

view the next input.

How to configure a wireless sensor and program a zone

Enter the Installer Menu 19

1. MENU Key, Installer PIN, ENTER

2. 19 ENTER

3. * (Advanced Installer Menu)

Enter the Remote Device Menu

4. 28 ENTER

Select the Wireless DGP and its Menu

5. 1 ENTER (1-DGP, 2-RAS)

6. 1 ENTER (DGP No)

7. 15 ENTER (Set Factory Defaults if not empty!)

8. * (Confirm)

9. 2 ENTER

10. 17 ENTER

11. 1 ENTER (always 1 zone)

12. Press Program Switch (tamper the sensor)

13. Keypad will beep 2 times to confirm that the zone has

learned properly

14. If ready press 0 ENTER to leave the zone programming

15. 0 ENTER (exit the DGP menu)

16. 0 ENTER (exit menu 28)

Enter the Installer Menu 19 again

17. ENTER (Simple Menu)

18. 1 ENTER (Zone database)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1234 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info