Bedienungsanleitung Aritech ATS7100 (Seite 10 von 24) (Englisch, Holländisch)

702286

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

10 ATS7100/7110 Installation and Troubleshooting Guide

LED LED 1 –

Status

LED 2 - Call

Status (B-

channel)

LED 3 - X25

Call Status

Off Hardware

failure

Offline Offline

Flash Operational

Call setup in

progress

Call setup in

progress

Blink Local S0 bus

failure

Incoming call

present

Pause

before

reconnect

On Line fault,

network

failure

Online Online

Table 2. ATS71xx status LEDs

Notes:

ATS7110 only

A running light on all the three leds indicates the unit

is initialising.

2.5. Programming the ATS7100

The minimum programming settings for the ATS7100

are:

Menu Description Comments

19.9 Reporting format Per Central Station

19.9 Phone number 1 Per Central Station

19.9 System account

number

Per Central Station

19.9 Area account number Per Central Station

and Area

19.9 Select ISDN dialler Per Central Station

19.9 Connection type 1 – ISDN

Per Central Station

For Panel firmware

V04.00.00 and

higher

Table 3. ATS7100 minimum settings

For further programming details see the ATS

2000/3000/4000/4500 programming manual.

2.6. Programming the ATS7110

The minimum programming settings for the ATS7110

are:

Menu Description Comments

19.9 X25 TEI value Belgium: 1

Netherlands: 2

19.9 X25 D-Bit Belgium: No

Netherlands: Yes

19.9 Reporting format X25 ENAI

Per Central Station

19.9 Phone number 1 Per Central Station

19.9 System account

number

Per Central Station

19.9 Area account number Per Central Station

and Area

19.9 Select ISDN dialler Per Central Station

19.9 X25 Account Code Per Central Station

19.9 Connection type 2 – ISDN-D

Per Central Station

For Panel firmware

V04.00.00 and

higher

Table 4. ATS7110 minimum settings

For further programming details see the ATS

2000/3000/4000/4500 programming manual.

Using Titan

In general no events will be reported to the Central

Station while Titan is on-line to the panel. Due to

shared resources some limitations apply when

connecting Titan to a system to which an ATS7110 is

connected.

• When Titan is used via J18 using the

ATS1830/ATS1834 cable, no events can be

reported via D-Channel X25 as long as the cable is

connected. Disconnect cable from panel when

ready.

• Start a local J18 Titan connection by typing

*<installer code>Enter, select menu 7. Do not

select installer menu 19, since doing so initiates

the transmission of the LB event. When the

ATS1830/ATS1834 cable is already connected, the

ATS7110 will not be able to transmit this event,

and both event reporting and Titan are blocked.

2.7. Line monitor/guard (ATS7100

and ATS7110 in B-channel

mode)

The line monitor is activated by setting the menu

“Activate ISDN line monitor” to “YES” (see menu 9). If

enabled, the ATS7100/7110 ISDN checks whether the

S0 bus is activated or not. If the S0 bus is not activated,

it will initiate an activate request to the network and wait

for 12 seconds for the S0 bus to be activated. If there is

no response from the network, the ATS7100/7110

ISDN disconnects the outgoing S0 bus (CONN4) from

the network by its internal relay and initiates another

activate request to the network.

If there is still no response, the network has failed. The

ATS7100/7110 ISDN will then report a line fault to the

panel. The outgoing S0 bus was probably not the cause

of the line fault and will therefore be re-connected to the

network. The ATS7100/7110 ISDN keeps trying to

activate until the network is back.

However, if the network does respond after

disconnecting the outgoing S0 bus (CONN4), the

outgoing S0 bus caused the line fault. The

ATS7100/7110 ISDN keeps the outgoing S0 bus

disconnected to ensure proper operation. From then on

it will reconnect the outgoing S0 bus every hour to test

whether the S0 bus problem has been solved or not.

This state will be remained until the S0 bus is

operational. As it is still possible to transmit alarm

events, there will be no line fault reporting to the panel.

2.8. Troubleshooting

 LEDs indicating operation/trouble mode (see table

4 and 5).

 Speaker connector

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS7100 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info