Bedienungsanleitung Arturia MicroFreak (Seite 81 von 104) (Englisch)

748333

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

13.1.3.2. Editing a sequence

Once you have entered the desired notes you can fine-tune the sequence, either by

changing the notes you've stored in a step or by adding modulation to a step:

• select the sequence you want to edit (A or B)

• make certain that "play" is turned off and press record

• turn the Rate/Swing encoder to "scrub" through the sequence.

The MicroFreak will play back all data stored in a step including modulation events you have

stored in the modulation tracks [p.77]. When you reach the end of the sequence, it cycles

back to the beginning.

If there is a step on which you want to change the stored data, select it with the encoder

and hold new notes to replace the ones that were previously stored in the step.

To erase the content stored in a step press the "Hold" icon; this inserts a rest in that step.

Note: When in step mode the active sequencer can also record notes and velocities you play

on an external keyboard into the MIDI In port.

Note: When in step mode, turning [Shift]+[Rate/Swing] allows you to change the length of the

sequence on the fly.

13.1.3.3. Real-time recording a sequence

Real-time recording is similar to recording on a loop pedal. In step recording, only the

Record icon is lit up. To record in real time, activate "play" and then press Record. When

the Record icon starts blinking the track is ready and waiting for you to play notes or knob

movements into it.

Note: When recording, notes will run continuously and record whatever you play replacing

what you have recorded in the previous loop. When recording modulation the sequencer

will run one cycle and then punch out (stop recording).

Real-time recording is very much a fun feature: you cannot make complicated edits, but

some editing is possible:

• If during recording you press a note, it will overwrite the current recorded

content.

• If you want to erase notes or modulation events in the sequence, press Hold

when recording is active at the moment these notes or events occur. They will be

replaced by silence, and you can fill them in during the next record cycle.

If your MicroFreak is connected to a computer running a DAW (a software sequencer) you

could prepare a complex sequence in the DAW, set the MicroFreak to Real-time recording

and press play on the DAW. It will take some experimentation to get this right, but it can be

done. At this point the Modulation tracks are still empty, so you can enhance the sequence

by recording knob movements on the modulation tracks.

Tip: When recording in real time the number of steps in a sequence becomes important;

more steps mean that you can record in a higher "resolution". You set the number of

steps in Utility>Preset>Seq length. Choosing a low recording rate helps to insert notes and

modulations with more precision.

Arturia - User Manual MicroFreak - The Sequencer 76

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arturia MicroFreak Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info