736695
41
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Maintenance
41
Checking when the engine is running
1. Start the engine.
ð The device must be stopped.
2. Pull the accelerator lever all the way up.
ð The engine is idling.
3. Repeat the test procedures for steering, drive lever and
cutting height.
ð Function is as described in the respective point.
ð The device must drive forward when you press the
right joystick forward.
ð The device must drive backwards when you press the
right joystick backwards.
ð The device must stop without delay when you press
the right joystick backwards.
Checking the safety functions
Magnetic contact switch on the transmitter holder
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Turn the accelerator lever to neutral position.
6. Remove the transmitter from the transmitter holder.
7. Turn the accelerator lever forward to slow speed.
ð The engine must stop.
Seat contact switch
1. Select the operating mode MC.
2. Insert the transmitter into the transmitter holder.
3. Sit down on the driver’s seat.
4. Switch on the transmitter and the receiver.
5. Start the engine.
6. Turn the accelerator lever forward to slow speed.
7. Carefully relieve the driver’s seat.
ð The engine must stop.
Magnetic contact switch on the transmitter holder
and seat contact switch
1. Select the operating mode MC.
2. Insert the transmitter into the transmitter holder.
3. Sit down on the driver’s seat.
4. Switch on the transmitter and the receiver.
5. Start the engine.
6. Turn the accelerator lever forward to slow speed.
ð The motor must not be stopped.
Checking the Emergency stop switch
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Move on a terrain where the blade can rotate freely and
does not touch objects or the ground.
6. Make sure that nobody is in the danger area of the device.
7. Engage the blade.
8. Press the Emergency stop switch on the device.
ð The blade must come to a standstill from full speed in
less than 5 seconds.
ð The engine must stop.
ð The status indicators on the device must be perman-
ently lit.
Checking the start-stop switch with key
1. Select the operating mode RC.
2. Switch on the transmitter and the receiver.
3. Start the engine.
4. Drive on large, open and level terrain.
5. Make sure that nobody is in the danger area of the device.
6. Drive slowly forward.
7. Press the start-stop switch.
ð The accelerator lever must go to neutral position/parking
brake.
ð The engine must stop.
ð The status indicators on the device must be permanently
lit.
Checking the key function
1. Press the start-stop switch.
2. Remove the key from the start-stop switch without turning
it.
3. Try to switch on the transmitter.
ð Without key the transmitter it must be impossible to turn
on the transmitter.
Checking the transport position of the
blade
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Move on a terrain where the blade can rotate freely and
does not touch objects or the ground.
6. Make sure that nobody is in the danger area of the device.
7. Move blade to transport position.
ð Now the blade should not engage.
41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AS Motor AS 940 Sherpa 4 WD RC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC Bedienungsanleitung - Deutsch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info