Bedienungsanleitung AS Motor AS 940 Sherpa 4 WD RC (Seite 42 von 60) (Englisch)

736695

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Maintenance

Checking the automatic blade switchoff

1. Select the operating mode RC.

2. Switch on the transmitter and the receiver.

3. Start the engine.

4. Drive on large, open and level terrain.

5. Make sure that nobody is in the danger area of the device.

6. Engage the blade.

7. Do not actuate for 2minutes any control element on the

transmitter.

ð After these 2minutes, the blade must be automatically

switched off.

ð The status indicators on the device must go out.

Checking the parking brake

Warning

If the parking brake is not properly adjusted, the device

can roll away.

► Make sure that the parking brake always functions cor-

rectly.

1. Place the device on a surface with a good grip (e.g. con-

crete or asphalt).

2. Switch off the engine.

3. Let the device cool down for at least 20minutes.

4. Unlock the drive.

5. Activate the parking brake.

6. Try to push the device.

If the rear wheels lock up, the parking brake is set correctly. If

the device can be pushed, the parking brake must be read-

justed by an authorised service centre.

Check in the MC mode if the accelerator lever moves to neut-

ral position (parking brake) when the brake pedal is activated.

Check in the MC mode if the accelerator lever goes back to

neutral position (parking brake) when the driver leaves his

seat.

Check the foot brake

Check in the MC mode if the accelerator lever goes back to

neutral position (parking brake) when the brake pedal is actu-

ated.

Checking the blade

Warning

Wear or damage on the blades and the fastening elements

can result in the blades or the fastening elements coming

off.

► Check the blades and all fastening elements according

to the following instructions.

Warning

There is a considerable risk of injury due to improperly

mounted and maintained blades.

► Work at blades must be carried out by an authorised

service centre.

Use solid gloves when you check the blade.

Work on the blade requires specific expertise because an im-

balance inspection is necessary and torques must be ob-

served.

Blades that are sharpened improperly increase the workload

of the device and can result in vibration cracks or breaks.

Check the blade and all fastening elements for wear, damage

and cracks

– each time before and after you mow.

– in case of noticeable changes or unusual vibrations.

Contact an authorised service centre if you detect faults or

damage during inspection.

All shown blade parts and their fastening elements must be

changed

– if damage or cracks are detected.

– if unusually strong vibrations occur.

– at least once a year or every 50 operating hours, no matter

if wear does exist or not.

The material weakens, can suffer cracks, endangering

people and material assets. Ejected broken pieces can cause

severe injuries.

Unusual vibrations are an indication that

– blades are missing or broken,

– the blade is worn excessively or on one side or

– damage to the engine or cutter deck fastening.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AS Motor AS 940 Sherpa 4 WD RC Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AS Motor AS 940 Sherpa 4 WD RC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info