Bedienungsanleitung AS Motor AS 940 Sherpa 4 WD RC (Seite 46 von 60) (Englisch)

736695

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Assembly

Scope of delivery

The device is shipped in a carton on a pallet. The scope of

delivery included:

– The device.

– The transmitter with batteries, belts and 2 keys for the

start-stop switch.

– Steering wheel.

– Tool bag with small parts.

– This operating manual.

– Manufacturer’s certificate.

– Operator’s manual of the engine manufacturer.

– Operating instructions for receiver and transmitter.

Unpacking

1. Remove the box.

2. Check the air pressure of the tires (see Technical data).

3. Insert the batteries into the transmitter (see Checking and

changing the battery).

4. Attach the belt to the transmitter.

5. Remove the spare key and keep it in a safe place.

Mounting

Mount the steering wheel:

1. Insert the screw(1) through the steering wheel and the

steering column.

2. Tighten the central fixing screw(3).

3. Screw the nut(2) onto the screw(1).

4. Fit the cap(4).

Storage

Warning

Danger of poisoning due to poisonous exhaust gases.

► Do not operate the engine in closed or insufficiently

ventilated rooms.

► Please observe the safety instruction regarding the

poisoning risk.

Warning

Fire hazard

Parts of the device can become extremely hot during oper-

ation and this may cause fire.

► Please observe the safety instruction regarding the fire

risk.

Warning

There is a risk of injury in case of unauthorised use.

► Press the start-stop switch on the transmitter, remove

the key and switch off the main switch when you do not

use the device any longer.

Storing the device

Keep the device in a closed, dry, and well ventilated room

and out of reach of children. Always eliminate all problems of

the device before you store it so that the device is always in a

safe-to-operate state. Let the engine cool down before you

store the device in closed rooms.

Also observe the notices on storage in the attached operating

instructions by the engine manufacturer.

Longer storage

1. Observe the safety instructions for handling the fuel.

2. Emptying fuel tank: Place a piece of hose onto the fuel

valve and let the fuel run into an approved fuel container.

3. Emtyping carburetor: Start the engine and let it run until it

stops by itself.

4. Thoroughly clean the device.

5. Touch up any possible damage to the paint finish (for

paint, see Accessories).

6. Remove the key from the transmitter and store it separ-

ately from the device.

7. Remove the batteries from the transmitter.

Before longer storage, e.g. in the fall, have an authorised ser-

vice centre check the device!

Also observe the notices on storage in the attached operating

instructions by the engine manufacturer.

Restarting

If you want to start the device after a longer storage, carry out

the tasks described in chapter Maintenance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AS Motor AS 940 Sherpa 4 WD RC Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AS Motor AS 940 Sherpa 4 WD RC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info