Bedienungsanleitung Asko w 620 (Seite 27 von 36) (Englisch)

309039

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Page 9

ENGLISH

COMMON LACOMMON LAUNDRUNDRY PRY PROBLEMSOBLEMS (CONTINUED) (CONTINUED)

ProblemProblem Possible CausePossible Cause Suggested SolutionSuggested Solution

Empty all pockets and turn inside out before laundering.

Fasten all hooks, snaps, and zippers before laundering to avoid snags.

Remove sharp buckles. Turn knits inside out.

Before washing, rinse harsh chemicals (such as battery acid, hair

care chemicals, cleaning solutions, etc.) from towels and other articles

to avoid holes in fabrics. Do not allow these unrinsed items to contact

other fabrics.

Mend all garments before laundering to prevent enlarging of rips.

These items may fray at edges from normal wear, not the washer.

Wash only in half loads and don’t wash in the same load with heavy

items, such as towels or jeans.

Rips, snags,

excess wear

Sharp objects in pockets

Hooks, snaps, zippers,

buckles

Harsh chemicals

Existing rips and tears

Permanent press items

Permanent press items should be washed in half-loads to prevent

wrinkling. If possible, use a slower spin speed.

Use lower wash temperature settings.

Excessive

wrinkling

Machine too full

Water too hot

ERRERROR MESSAOR MESSAGES – GES – W640/W660W640/W660

Error messages will display in the LED window if faults

occur while a program is in progress. The table below

defines each possible error message.

ERRERROR MESSAOR MESSAGEGE SOLSOLUTIONUTION

When this symbol flashes at the lower right corner of the display it merely means

the glass door isn’t closed securely. Close the door and try again.

0000 If this message flashes at the top right of the LED window, the machine has failed

to spin. This could be because the load is out of balance. Turn the power off

then on again. Open the door and redistribute the washing. Run the Spin

program again.

Door lock fault Call a service technician.

Foaming Run the Rinse program again.

Try using less detergent and softener.

Use low-sudsing detergents. (See page 5.)

Overflow Call a service Technician

Pressure sensor Call a service technician.

Temperature stop Call a service technician.

Thermistor Call a service technician.

Wash motor Call a service technician.

Water inlet Make sure the water tap is open.

Water outlet Check the pin trap for possible blockage. Make sure the outlet hose isn’t kinked.

To remove the message, turn the power off or change

the program.

FFAAULULT CODES – T CODES – W600/W620W600/W620

The Program Control knobs on the W600/W620 have

two fault codes: C and S. If the knob stops on one of

these, the machine detected a problem.

C PositionC Position

This indicates a problem that can probably be taken

care of without calling a service technician. Here are

some possible problems:

♦ Power interruption.

♦ Water not draining out.

♦ Water not filling machine.

♦ The machine didn’t spin.

Refer to the “Troubleshooting” section on the next page

for possible causes and solutions. If none of these

work, call a service technician.

S PositionS Position

If the knob stops on S, this indicates a mechanical

problem and you will probably need to call a service

technician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Asko w 620 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Asko w 620

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info