Bedienungsanleitung Astralpool ASTRALPOOL HEAT II (Seite 25 von 196) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

673144

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

ASTRALPOOLHEAT SERIES · AIR/WATER SYSTEM

ASTRALPOOLHEAT SERIES · AIR/WATER SYSTEMASTRALPOOLHEAT SERIES · AIR/WATER SYSTEM

ASTRALPOOLHEAT SERIES · AIR/WATER SYSTEM

Pag:

ENGLISH

ENGLISHENGLISH

ENGLISH

POOL

POOL POOL

POOL &

SPA MODE

SPA MODESPA MODE

SPA MODE

When the unit is configured to heat Pool and Spa water, we can use both terminals, EXT #1 and

EXT #2, to gain some extra capabilities (first SPA Control screen on technical menu has to be set

to External control, see 5.7. 17).

5.16.

5.16. 5.16.

5.16. MODBUS

MODBUSMODBUS

MODBUS

This Heat pump includes Modbus capabilities. For complete instructions

for Modbus connection & communication, please consult Modbus manual

at Fluidra PDB (Product Data Base): http://pdb.astralpool.com/pdb/

6. 6.

6. START

STARTSTART

START-

-UP PROCEDURE FOR THE UNIT

UP PROCEDURE FOR THE UNITUP PROCEDURE FOR THE UNIT

UP PROCEDURE FOR THE UNIT

Operating requirements for the heat pump:

• The outdoor temperature must be higher than +5 ºC.

• The heat pump is provided with a defrost thermostat that guarantees compressor

shutdown and the operation of the defrost system.

• When washing the filter of the filtering pump, it is MANDATORY to turn off the heat

pump.

Before any start-up, you should check:

• The correct clamping of the hydraulic connections (exchanger inlet / outlet).

• The correct fastening of the electrical cables to the connection terminals. Poorly

secured terminals can cause the terminal block to heat up.

• When setting-up, the electrical connections, as well as the general power supply and

voltage should be verified.

• Once the unit is connected, verify the intensity absorbed by the phases and check that

the fan is operating in the correct direction.

• Give power to the equipment by connecting the general power switch on the outside of

the unit. Once the unit is connected, verify the intensity absorbed by the phases.

• Three-phase units have a phase control relay that guarantees the compressor is

operating in the correct direction. If the controller shows the compressor it is running

and it does not, phases must be interchanged. Card gives an alarm signal.

• With the machine running, verify the intensities absorbed by the electric motors,

making sure they do not exceed the limits mentioned in the technical specification

sheet.

• Verify that the currents of the different lines are not out of phase except in the case of

single-phase circuits.

• High and low pressure switches should be installed in the cooling circuit and verify the

refrigerant charge (Refrigerant Charge section).

Performing the heat pump adjustments in its initial operation

EXT #1

EXT #

RESULT:

The unit will work on Pool mode.

The unit will work on Spa mode

The unit will work on Pool + Spa mode

External Stop (same case as in general mode)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Astralpool ASTRALPOOL HEAT II Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info