Bedienungsanleitung Astralpool Viron eVo (Seite 6 von 20) (Englisch)

673158

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Inst.296 Viron eVo Series Pool & Spa Heater V07_16

MAINTENANCE

It is recommended that you check the following at least every six months and at the beginning of every swimming

season.

1. Examine the flue outlet and panel louvers for blockages. Make sure there are no obstructions to the flow

of air to or from the appliance.

2. Keep the heater area clear and free of combustibles and flammable liquids. Chlorine should not be stored in

the vicinity of the heater. Chlorine and acid vapours, when drawn through a heater, can rapidly cause

corrosion of the heat exchanger.

3. Keep the heater area free from garden refuse and debris. This will help prevent insects nesting in the unit

and ensure extended life and reliability of your heater.

4. Have your heater professionally inspected at least every 2 years, preferably every 12 months.

WINTER OPERATION

If the pool won’t be used for a month or more, turn the heater off at the main gas isolation valve. For areas where

there is no danger of freezing, water should circulate through your heater all year long even though you are not

heating your pool.

Where freezing is possible, it is necessary to drain the water from the heater. This may be done by loosening the

inlet or outlet barrel union. If the heater is below water level, isolate it from the pool first by closing shut off valves

before and after the heater.

CAUTION: If the heater has been drained for freezing conditions, do not turn on until the system is circulating

water.

INSTALLATION

THIS APPLIANCE MUST BE INSTALLED BY AN AUTHORISED PERSON. Refer to heater data plate for

specifications of gas type, gas consumption, burner pressure and water pressure.

This appliance must be installed in accordance with local regulations and Australian Standard Installation Code

AS/NZS 5601.

The installer must test the operation of the appliance before leaving.

FLOW RATES

The Viron eVo Pool Heater requires a minimum of 250 litres per minute flow for 250/350 models and 350 litres per

minute flow for 450/550 models. The maximum permissible flow rate is 500 litres per minute. For flow rates in

excess of 500 litres per minute, an external by-pass valve must be fitted.

WATER CONNECTIONS

The heater should always be installed after the pump and filter. The water connections are located on the right

hand side of the heater. The inlet and outlet are clearly marked. Water connections must be completed in 50

mm PVC glue in plumbing.

All automatic sanitising devices must be installed after the heater and in such a way that the sanitiser cannot enter

the heater without first mixing with the water in the pool or spa. Sanitisers that are connected prior to the heater will

void heater warranty.

A non return valve is not required to be fitted between the filter and the heater.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Astralpool Viron eVo Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info