Bedienungsanleitung Astralpool Viron eVo (Seite 11 von 20) (Englisch)

673158

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Inst.296 Viron eVo Series Pool & Spa Heater V07_16

600

Approved gas

termination cowl

1500

Upper grille for fresh air

ventilation

Lower grille for fresh air

●

ventilation

Do not install spa blowers in the same room as a gas heater. This is potentially dangerous to spa users.

Do not store chemicals or fuel in the same room as the gas heater. This may cause fire or explosion.

When installing in a garage the Viron Series Heater must be installed 450 mm above floor level.

ELECTRICAL CONNECTION

The heater is supplied with a standard 10 amp 3 pin plug for connection to a 240V 10 amp GPO. All pool or spa

equipment connected to mains power should be protected by an RCD circuit breaker.

GAS CONNECTION

The gas connection is on the right hand side of the heater. A 22mm M.I. connection is provided for gas line

connection. An approved manual shut off valve must be installed in the gas fitting line before the heater.

The gas fitting line should be installed by an authorised person and comply with local regulations and Australian

Standard code AS/NZ 5601. The gas line from the meter will usually be of a larger size than the gas inlet

connection.

The heater gas valve has a built in pressure regulator and ⅛” pressure test point. On starting the heater, a

manometer must be used and the supply inlet pressure checked while the heater is running against the heater

data plate. Incorrect inlet pressures may void warranty and may result in service charges, should service be

required. Gas valves are preset and should only be adjusted by trained Astral Pool technicians.

PRESSURE SWITCH ADJUSTMENT

The Viron Pool Heater incorporates a water pressure switch which allows the burner to operate only when the

circulating pump is operating. The pressure switch is designed to operate with the heater installed up to 1.2

metres above or below the surface level of the pool or spa. For installations outside these limits, a flow switch

should be installed.

It is imperative that the following be undertaken by the person who is commissioning (first starting) your pool or

spa heater. On initial start up of the heater it may be necessary to adjust the water pressure activation switch.

This switch is located behind the top right hand side panel and is screwed into the water manifold. The pressure

switch is a safety device, designed to allow operation of the heater only when the circulating pump is on and there

is sufficient water flow through the heater. It must shut the heater down immediately the pump is switched off.

To check the operation of the switch:

1. Connect the heater to mains power supply and turn power on. The thermostat should not yet display “θ”.

2. Turn on pump. The thermostat should now display “θ”.

3. Turn pump off. The thermostat should no longer display “θ”.

4. If display does not respond in this way, adjust the pressure switch as detailed below. If display responds

correctly, perform a final check with the heater operating.- See the section below titled “Starting the heater”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Astralpool Viron eVo Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info