Bedienungsanleitung ATAG KD 8102 AD (Seite 19 von 27) (Deutsch, Englisch, Holländisch, Französisch)

75802

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

* Depending on model and options

W Remove the shelves as shown in the

illustration:

- Lift the glass shelf*, align the recess over

the support, tilt to the side and remove

towards you at an angle.

- Always insert shelves with the raised

edge or guard bar at the back pointing

upwards, otherwise food may freeze

onto the rear wall.

W Always remove the top door rack (butter

and cheese compartment) together with

the flap*. Then press one of the side

walls carefully to the outside to release

the flap pin. The flap can then be lifted

out.

- The shelves and door racks can be dis-

mantled for cleaning. Remove the trims

and sides from the glass shelves.

- Remove the protective film from the

decorative trims.

W Clean the drain hole on the rear wall above the vegetable

bins frequently,

arrow in illustration. If

necessary, clean with a thin object,

e.g. a cotton swab or similar.

W Then connect/switch on the appliance and

insert the food to be frozen.

If the appliance is to be

left switched off for any length of time

empty the appliance, disconnect from the mains, clean as described

above and leave the door open so as to avoid odours.

Troubleshooting

Your appliance is designed and manufactured for a long life span

and reliable operation.

If a malfunction nonetheless occurs during operation, check

whether it is due to an operating error. Please note that even

during the warranty period the resultant servicing costs in this

case will have to be borne by the owner.

You may be able to rectify the following faults by checking the

possible causes yourself:

Malfunction - Possible cause and remedy

______________________________________________

Appliance does not work, display is off

- Is the appliance switched on properly?

- Is the mains plug properly inserted in the socket?

- Is the socket fuse intact?

The interior light does not come on

- Is the appliance switched on?

- Has the door been open for more than 15 minutes? The interior

light switches off automatically after the door has been opened

for approx. 15 minutes.

- If it does not switch on when the door is opened briefly, but the

temperature display is working, it may be defective.

Mains Voltage

Important! To prevent injury or damage, always ask our

customer service department to carry out any repairs and

replace the LED interior light.

Caution - class 1M laser radiation. When cover

is removed, do not look directly at light through

optical instruments.

Loud running noise

- Is the appliance standing firmly on the floor, or does the com-

pressor cause nearby items of furniture or objects to vibrate?

If necessary, move bottles and containers apart.

Burbling noises are normal. These are caused by the refriger-

ant flowing round the refrigerant circuit.

A short

clicking sound: This will be heard whenever the

refrigeration unit (the motor) switches on or off automatically.

Motor noise: This will be slightly louder for a brief period when

the refrigeration unit switches on.

The temperature is not cold enough

- Is the temperature setting correct? If necessary, set a lower

temperature and check the display after 24 hours.

- Does the door close properly?

- Is the appliance built in properly?

- Is the appliance sufficiently well ventilated?

Clear ventilation grilles if necessary.

- Is the ambient temperature too hot? (See "Safety regula-

tions")

- Has the appliance been opened too often or left open too

long?

- If applicable, wait until the appliance reaches the required

temperature itself.

Customer service and type plate

If none of the above causes apply and you cannot rectify

the fault yourself, or if the temperature display reads "F 0"

to "F 5", this means that there is a fault. Please contact your nearest

customer service department (see enclosed list for addresses),

indicating the

fault number displayed, together with the

type designation 1,

service number 2 and

serial number 3

as given on the type plate. This

will help us to provide you with a

faster and more accurate service.

The type plate is located inside the

appliance on the left-hand side.

Leave the appliance shut until

the customer service engineer

arrives so as to prevent any further

cold loss.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG KD 8102 AD Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info