Bedienungsanleitung ATAG VA7015NT (Seite 15 von 24) (Englisch)

692635

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Upper spray arm

• The upper basket must be removed before the upper spray arm

can be released. Pull out the upper basket and turn the basket

catch on each runner outwards (see illustration). The basket can

now be removed.

• Pull the upper spray arm straight up to release it.

Lower spray arm

• Pull the lower spray arm straight up to release it.

The door and the door seal

Regularly clean the sides of the door and the door seal. Use a slightly

damp cloth (with a little cleaner if necessary).

Front panel

Keep the buttons clean and free from grease. Wipe them clean with a

dry or slightly damp cloth. Never use cleaners – they can scratch the

surface. Use the main power switch to turn off the dishwasher before

cleaning the buttons to avoid activating any buttons unintentionally.

The dishwasher tub

The dishwasher tub is made of stainless steel and is kept clean through

normal use.

Limescale deposits

If you have hard water, limescale deposits may build up in the

dishwasher. If this happens, run the Intensive programme with two

tablespoons of citric acid in the detergent compartment (with no dishes

in the machine). Special dishwasher cleaners are also available on the

market.

Unblocking the drainage pump

If the dishwasher still contains water after the programme has finished,

something may be blocking the drainage pump. Such items are easily

removed.

1 Turn off the machine using the main power switch and unplug it

from the wall socket.

2 Remove the coarse filter and the fine filter.

3 Scoop out the water from the dishwasher tub.

4 In order to inspect the drainage pump, remove the coloured stop

on the right in the bottom drain.

5 Turn the pump wheel located behind the drainage pump stop by

hand. Carefully remove any items.

6 Refit the drainage pump stop along with the fine and coarse filters.

7 Plug the machine in again.

If the dishwasher still does not start and a whirring sound is heard,

the overflow protection has been activated.

• Shut off the water.

• Remove the plug from the wall socket.

• Call the service department.

Drainage pump stop

NOTE!

Do not forget to refit the drainage pump stop.

Unblocking the inlet hose filter

If the water supply contains small particles, the outer filter on the inlet

hose may become blocked, which results in Water inlet fault.

1 Turn off the machine using the main power switch and unplug it

from the wall socket.

2 Turn off the water tap.

3 Unscrew the inlet hose.

4 Carefully remove the outer filter from the inlet hose and clean it.

5 Refit the filter and check that the gasket is correctly positioned.

6 Screw the inlet hose firmly into place.

7 Plug the machine into the wall socket and turn on the water tap.

Allow the pressure to settle for a while and check that the connection

is watertight.

Outer filter on inlet

hose

Gasket

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG VA7015NT Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG VA7015NT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info