Bedienungsanleitung Atika BKS 38 A (Seite 27 von 135) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

475723

Zoom out

Zoom in

Vorherige Seite

1/135

Nächste Seite

Chain catcher

The chain catcher (30) prevents a broken or jumped off saw

ed.

chain from hitting the operator during sawing.

LCheck the chain catcher on a regular basis and replace

it if it is damag

Silencer / exhaust outlet

 Check the tight seat of the screws on the silencer (25) on a

regular basis

Î If they are loose,

tighten them hand-tight with the engine

in cold condition.

Do not retighten the silencer screws when the engine is

L Clean the exhaust outlet on a regular basis

Adjusting the carburetor (idle speed)

the correct fuel-air mixture is fed to the engine.

in severe

engine damages. Do not continue working with the

ed) has to be

in idle speed)

- Err

LC d have the carburetor

The carburetor is factory-set to the correct idle speed so that

An incorrect carburetor adjustment results

chain saw in such a condition.

In the cases below the carburetor (idle spe

corrected:

- Speed too high (saw chain continues to move

atic running or lack of acceleration (idle speed too low)

justment to weather conditions and temperatures

ontact a specialist workshop an

- A

adjustment done.

Cleaning

Clean the chain saw thouroughly after each application so that

ith a soft brush or a dry cloth.

the faultless function is kept.

B Clean the case w

Water, solvents and polishing agents shall not be

applied.

B Make sure that the vent slots (32) of the cover (26)

ting).

aw using a

and the engine's cooling fins (33) for engine cooling are free

and clean (risk of overhea

If heavily contaminated, clean the chain s

commercial chain cleaner.

Â Clean the oil flow canal (19) with a clean cloth or a

sh.

bru

B Â

Clean the brake strap (20) at the cover (13) using a

brush.

Before each transport:

− switch off device

− wait for stop of chain saw

− attach the scabbard on the guide bar

 Â Carry the product with the front handle. The guide bar

When transporting the product within a car put it in the boot

o e the chain saw against

tip i

sha l show to the rear side.



n a separate loading area. Secur

p ng over, damages and fuel spillage.

guarantee smooth

operation, before storing for a longer period:

B Operate the engine buretor is empty.

B thoroughly clean th

longer

stem should be flushed

commercial chain saw

the

B Aft

sho

 Store unused equipment in a dry, locked place out of the

reach of children.

To extend the service life of the saw and



until the car

e device.

B Empty the fuel tank completely.

B Empty the oil tank completely.

B C Dispose of remainders of fuel/saw chain oil according

to relevant regulations (environmentally compatible).

Tipp:

ncrustations after a

Some chain oils tend to e

period. For this reason the oil sy

before a longer storing with

cle

aner. Fill the cleaner up to the middle (appr. 50 ml)

into the empty oil tank. Close the tank. Operate the chain

ithout installed guide bar and chain until all of

saw w

cleaner came out of the oil outlet of the chain saw.

er cleaning, immerse the saw chain in an oil bath for a

rt time and wrap it then with oiled paper.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BKS 38 A Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info