Bedienungsanleitung Atika BSV315 (Seite 16 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch, Schwedisch)

520774

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Safe working

Woodworking machines can be dangerous if not

used properly. If electrical tools are used, the fundamental

safety precautions must be met to preclude the risks of

fire, electric shock and injuries to persons.

Before starting this device, read and keep to the following

advice. Also observe the preventive regulations of your

professional association and the safety provisions appli-

cable in the respective country, in order to protect yours-

elf and others from possible injury.

Pass the safety instructions on to all persons who work

with the machine.

Keep these safety instructions in a safe place.

 Make yourself familiar with the equipment before using

it, by reading and understanding the operating instruc-

tions.

 Be attentive. Be careful what you do. Behave sensibly

when working. Do not use a power tool while you are

tired or under the influence of drugs, alcohol or medi-

cation. A moment of inattention while operating power

tools may result in serious personal injury.

 Do not overreach. Provide a safe standing position and

keep at any time the balance.

 Wear suitable work clothes:

− Do not wear loose-fitting clothes or jewellery, they could

be caught by movable parts.

− - slip-proof shoes

− Hairnet in case of long hair

 Wear personal protective equipment:

− Ear protection (the noise level on the workplace may

exceed 85 dB (A))

− Safety goggles

− Dust mask with work activities generating dust

 Only operate the band saw on a

− firm

− level

− slip-free

− vibration free surface

 Keep your workplace in an orderly condition! Untidiness

can result in accidents.

 Provide a safe standing position and keep at any time the

balance. Do not lean forward.

 Take environmental influences into consideration:

− Do not expose the machine to rain.

− Do not use the machine in humid or wet environment.

− Provide for good illumination.

− Do not use this machine near inflammable liquids or

gases.

− The wood dust generated during operation impedes the

necessary view and is harmful to health to some

degree. Unless the machine is used outdoors, it must

be connected to a chip exhaust system (e.g. portable

dust remover).

 Never leave the machine unattended.

 Persons under the age of 18 must not operate the band

saw. An exception is youngsters under the age of 16

within the scope of their vocational training under super-

vision.

 Keep other persons away.

Do not allow other persons, especially children

, to touch

the tool or cable.

Keep them away from your working area.

 Take the correct working position. The saw teeth must

show to the operator.

 Only begin cutting after the saw band has reached its re-

quired rotational speed.

 Do not force the power tool. You work better and safer in

the given performance range.

 Only operate the machine with complete and correctly

attached safety equipment and do not alter anything on the

machine that could impair the safety.

 Do not use any cracked saw bands or such that have

changed their shape.

 Use only sharp saw bands since dull saw bands not only

increase the danger of back kicking but also cause exces-

sive load on the motor.

 Do use only saw bands according to ISO 3295 / DIN 8806-

The use of other tools and other accessories may

present a risk of injury to you.

 Do not use the saw for purposes it is not intended for (see

proper use).

 When longitudinally cutting narrow workpieces (distance

between the saw blade and the parallel rip fence less than

120 mm), use the pushstick. (see “working instructions”).

 To push narrow workpieces against the parallel rip fence,

use a push block.

Î Push blocks can be purchased in retail outlets.

 Do not use defective pushsticks and blocks.

 See to it that the pieces cut off are not caught and thrown

away by the saw band.

 Do not remove the splints, splinters and wastes with the

hand out of the danger zone of the saw band.

 Cutting round timber is not allowed with the standard feed-

ing assistances. When cutting round timber use a special

device which safes the work piece from skewing.

 Switch the machine off and remove the mains plug from

the socket when

− carrying out repair works

− maintenance and cleaning

− carrying out servicing and repair works, removal of

faults (this also includes removing clamped splinters)

− checks of connecting lines, whether these are knotted

or damaged

− transporting the saw

− saw band exchange

− leaving the saw unattended (even during short interrup-

tions)

 Maintain your machine with care:

− Keep your tools sharp and clean in order to be able to

work better and safer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BSV315 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info