Bedienungsanleitung Atika BSV315 (Seite 17 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch, Schwedisch)

520774

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

− Follow the maintenance instructions and the instruc-

tions for tool exchange.

− Keep the handles dry and free of oil and grease.

 Check the machine for possible damage:

− Before further use of the machine the safety de-

vices and any parts that show minor damages must

be checked carefully for their proper and intended

function.

− Check whether movable parts function perfectly and do

not stick or whether parts are damaged. All parts must

be correctly installed and fulfil all conditions to ensure

perfect operation of the machine.

− Damaged safety devices and parts must be properly

repaired or exchanged by a recognized, specialist

workshop; insofar as nothing else is stated in the in-

structions for use.

− Damaged or illegible safety labels have to be replaced.

 Do not allow any tool key to be plugged in!

Before switching on, check always that wrenches and ad-

justing tools are removed.

 Store unused equipment in a dry, locked place out of the

reach of children.

Electrical safety

 Design of the connection cable according to IEC 60245 (H

07 RN-F) with a core cross-section of at least

− 1.5 mm² for cable lengths up to 25 m

− 2.5 mm² for cable lengths over 25 m

 Long and thin connection lines result in a voltage drop. The

motor does not reach any longer its maximal power; the

function of the device is reduced.

 Protect yourself against electric shocks. Avoid body

contact with grounded parts (e.g. pipes, heating apparatus,

cookers, fridges etc.).

 Do not use the cable for purposes for which it is not meant.

Protect the cable against heat, oil and sharp edges. Do

not use the cable to pull the plug from the socket.

 Check regularly the cable of the saw and get possible

damages repaired by an accepted specialist.

 When running the connection line observe that it does not

interfere, is not squeezed, bended and the plug connection

does not get wet.

 Regularly check the extension cables and replace them if

they are damaged.

 Do not use any defective connection cables.

 When working outdoors, only use extension cables especi-

ally approved and appropriately labelled for outdoor use.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 Only hook up the machine by means of a fault-current

circuit breaker (30 mA).

The electrical connection or repairs to electrical parts of

the machine must be carried out by a certified electrician

or one of our customer service points. Local regulations –

especially regarding protective measures – must be ob-

served.

Repairs to other parts of the machine must be carried out

by the manufacturer or one of his customer service

points.

Use only original spare parts, accessories and special

accessory parts. Accidents can arise for the user through

the use of other spare parts. The manufacturer is not liab-

le for any damage or injury resulting from such action.

Assembly

Assemble the base frame. Therefore, fasten the legs (A) with

each time 8 screws M8 x 16, flat washers A 8,4 and screw

nuts M8 at the frame (B).

Fasten the saw on the base frame.

Assemble the handle (11).

Open the upper case door (2).

Replacing the saw band

Danger of cutting! Wear gloves when replacing the saw

band.

1. Open both case doors (2 / 7).

2. Put upper saw band coping (19) completely down.

3. Put upper band roll (17) down

° turn the adjusting wheel (1) anti-clockwise, the saw

band is relaxed

4. Insert the saw band.

L Pay attention to a correct position: the teeth must

show forward (direction door).

5. Put saw band centrally on the band roll (17).

6. Turn adjusting wheel (1) clockwise until the saw band does

not glide off any longer.

Before going on assembling carry out the following adjust-

ments:

° Clamp saw band (see „Saw band tension“ p. 18)

° Adjust saw band (see „Incline of the upper band saw roll” p.

18)

° Adjust band guidances (see „upper band guidance“ and

„lower band guidance“ p. 20)

Assemble saw table

Assemble the end stop screw (M6 x 35) at the bottom side of

the saw table (13).

Guide saw table (13) over the saw band and put it on the saw

table guidance (20).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BSV315 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info