Bedienungsanleitung Atika BWS 400 (Seite 12 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

520796

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Assembling the saw blade casing and saw blade

E1 Release the locking nut (17) and pull off the flange (14 / 16).

E2 Insert the screws through the hole of the saw blade casing

(13). Afterwards, attach washers on the screws.

E3 E4 E5 Mount the saw blade casing (13). Fasten the casing with

washers and nuts.

E6 E7 Insert the saw blade cover (7) in the guide of the jigging

device and secure it using the screws.

E8 E9 E10 Fasten the guide (d) of the saw blade cover.

Tighten the screw only by hand and then slacken the nuts by

a half turn. The guide must move freely.

E11 Slide the saw blade flange (16) on the motor shaft.

E12 Danger of cutting! Wear gloves.

Mount the saw blade.

L Pay attention to the saw blade’s sense of rotation

(note the arrow on the saw blade and on the saw blade

casing).

E13 E14 Slide the saw blade flange (14) and the washer on the motor

shaft . Secure these parts using the locking nut (17).

E15 E16 E17 Mount the cover (18).

Assembling the handles

F Screw the handles (19) on the jigging device.

Assembling the support extension

G1 Insert the support extension (20) into the jigging device. Secure the

support extension with the star grip knob (21).

G2 Fasten the chain (8) onto the support extension.

Assembling the length stop

H Insert the length stop into the jigging device. Secure the length stop

with the star grip knob (21).

Before the first start-up

To achieve flawless functioning of the machine, please follow the

instructions listed:

 Place the saw at a location which meets following conditions:

− outdoor

− secured against slipping

− free of vibrations

− even

− free of tripping hazards

− adequate light

 To ensure a safer foothold when working with the saw secure the saw

against rolling away.

 Before each use, check

− connection cables for defects (cracks, cuts, etc.)

Do not use any defective cables.

− that the plastics insert is in a proper condition

− the saw blade for flawless condition

− the functioning of the jigging device

 Do not use any cracked saw blades or such that have changed their

shape.

 Do not use any saw blades made of HSS steel.

 Immediately replace a worn or damaged plastics inserts.

 Assume the correct work posture. Stand in front of the operating side

frontally to the saw blade line.

Start-up

Rotational direction of the saw blade

Ensure that the rotational direction of the saw blade is the same as

the rotational direction given on the saw blade casing (13).

Selection of saw blades

Consider when selecting the saw blade, that no edgeless or damaged saw

blades are used and that the diameter of the blade location hole is 30 mm

(note the nameplate on the machine).

L Mains connection

Compare the voltage given on the machine model plate e.g. 230 V with the

mains voltage and connect the machine to the relevant and properly earthed

plug.

L Use a shockproof plug, mains voltage 230 V with residual current

circuit breaker (FI switch 30 mA).

L Main fuse: 16 A inert

On/Off switch

Do not use any device where the switch can not be switched on and off.

Damaged switches must be repaired or replaced immediately by the

customer service.

Characteristic data of noise

Press the green button ( I ) on the switch.

If there is a power cut, the machine switches

off automatically. Push the green ( I ) button

to start the machine again.

Switching off

Press the red button (O) or the red button of the yellow switch

cover.

The built-in motor brake will decelerate the saw blade up to the

dead stop within 10 seconds.

The saw must not be used if the brake is defective, i.e. if the time

up to the saw blade’s dead stop exceeds 10 seconds.

Motor guard

The motor is equipped with a guard switch and it switches off

automatically when overload. The motor can be switched on again

after a cooling-down period (approx. 5 – 10 mins.).

Working with the saw

Before starting to work consider the following safety advices to keep the

risk of injuries as small as possible.

 Saw blade, plastics inserts and recuperating spring o. k.?

 Workplace tidied?

 You may not start to operate the machine until you have read these

operating instructions, observed all the instructions given and installed

the machine as described!

Before making adjustments to the saw settings (e.g. replacing the saw

blade etc.)

− switch off device

− wait for standstill of the saw blade.

− pull out power plug

Also, note the following important points:

 Place yourself outside of the area of danger.

 Place the wood piece in the jigging device. Cut through the piece with

uniform pressure.

 Never remove loose splinters, chips, or similar by hand.

At any case pay attention to all safety instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BWS 400 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info