Bedienungsanleitung Atika BWS 400 (Seite 13 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

520796

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Working instructions

1. Place the wood piece in the jigging device.

Only wood pieces with a max. diameter of 12 cm are allowed to be

sawed.

 Pull out the support extension (20) to the desired length and fix it

using the star grip knob (21). G3

 You will get pieces of equal length if you pull out the length stop

(22) and fix it in the desired position using the star grip knob. H

2. Hold the handle (19) on the jigging devcie with both hands and push the

jigging device uniformly towards the saw blade. Avoid erratic

movements.

L The barbs on the jigging device prevent any turning of the wood

piece during sawing.

 Do not force the jigging device against the saw blade, the motor

speed should not drop too far.

3. After cutting, the jigging device is automatically brought back to its home

position by spring force.

L In the home position, all of the saw blade (incl. cutting teeth) is

covered by the saw blade casing.

L If the recuperating spring (10) is broken or worn, the jigging

device will not automatically return to its home position. Replace the

recuperating spring.

Never saw without or with a damaged recuperating spring.

4. Only advance the wood piece after a completed sawing operation.

Maintenance and cleaning

Before each maintenance and cleaning work

− Switch off device

− Wait unitl the saw blade comes to a stop.

− Pull out power plug

Maintenance and repair work other than those described in this chapter is

only allowed to be carried out by service staff.

For maintaining and cleaning, removed security devices must unconditionally

be mounted properly and proved again.

Use only original parts. Other parts can result in unexpected damages and

injuries.

Cleaning

L Observe the following to maintain the operability of the machine:

 Do not wash down device with water.

 Remove shavings and dust only with a brush or vacuum cleaner.

 Clean and oil all moving parts regularly.

L Never use any grease!

 Use for instance sewing machine oil, liquid hydraulic fluid or

environmentally acceptable spray oil.

 Take care that the saw blade remain free of rust and resin.

 Remove resin residues from the push frame surface.

Resin residues can be removed with a commercial maintenance and care

spray.

 The saw blade is a wearing part and will become dull after prolonged or

frequent use.

 Renew the saw blade or have it sharpened

Maintenance

Changing the saw blade

Remove the mains plug before changing the saw

blade.

Danger of cutting! The saw blade is massive and it could be to slick.

Wear gloves when replacing the saw blade.

 Do not use any saw blades made of HSS steel.

 Do not use any cracked saw blades or such that have changed their

shape.

 Only use well-sharpened saw blades.

Danger of burning! The saw blade is still hot shortly after cutting.

1. Remove the cover (18). E15

2. Release the locking nut (17). E14

3. Now, the front saw blade flange (14) and the saw blade (15) can be

removed.

L Clean the saw blade flanges (14, 16).

5. Install a new or sharpened saw blade. E12

L Pay attention to the correct running direction of the saw blade: The

arrow on the saw blade and the arrow on the saw blade casing must point

in the same direction!

6. Position the front saw blade flange again. E13

7. The further assembly is now done in reverse sequence.

8. Check that the cover (18) is properly secured.

Replacing the plastics insert

Immediately replace the worn or damaged plastics inserts (24).

1. Loosen the screws of the plastics insert and remove them.

2. Insert a new plastic insert and screw it tightly in place.

Replacing the recuperating spring

Immediately replace a worn or damaged recuperationg spring.

1. Remove one end of the safety chain (12). D

2. Remove the cotter pin (9) and pull out the bolt (6)from the bracket. B2

3. Remove the recuperating spring (10).

4. Slide a new recuperating spring on the bolt.

5. The further assembly is now done in reverse sequence.

Transport

Remove mains plug before each transport.

Storage

Pull out power plug

+ Store unused equipment in a dry, locked place out of the reach of children.

+ Before a longer period of storage carry out the following to extend the saw

service life and ensure an easy operating:

− thoroughly clean the device

− treat all movable parts with an environmentally friendly oil

L Never use any grease!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BWS 400 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info