Bedienungsanleitung Atika KGS210N (Seite 18 von 141) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

520784

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

Dust bag

 When using the dust bag:

° push the dust bag (21) onto the exhaust neck (22).

° regularly empty the dust bag

Chip exhaustion

Connect a chip exhaust system with suitable adapter to the

chip exhaust neck (22) (dia. 40 mm).

L Air velocity at the exhaust neck of the saw ≥ 20 m/sec

Use a special exhaust device when exhausting dusts that are

especially harmful to health, carcinogen or dry.

Adjusting the saw

Pull the mains plug before performing

settings.

Setting the work piece stop

L To adjust a work piece stop that has shifted during

transport, proceed as follows:

1. Set the rotary table (8) to the 0° position and tighten the

fastening bolts for the rotary table (6) (see "Straight cuts").

2. Position the saw head in transport position (see "Transport")

3. Check the angle between saw blade and work piece stop

using a square (A, not supplied).

4. Loosen the locking screw for the work piece stop if the work

piece stop (18) needs to be adjusted

5. Align the work piece stop along the square and tighten the

locking screw again.

Adjusting the incline of the saw head

L Also check the angle of the saw head to the rotary table.

1. Check the angle with a square (A, not supplied) or protractor.

Proceed as follows if the angle is not exactly 90°:

• First loosen the incline locking knob (20) and turn the

saw head slightly to the side.

• Then loosen the locking nut (23) for the set screw (12)

° Turn the set screw (12) back to reduce the angle be-

tween saw head and rotary table.

° Turn the set screw (12) forward to reduce the angle

between saw head and rotary table.

• Tighten the locking nut for the set screw once more.

• If necessary, loosen the screw for the indicator (24) and

shift it until it points to "0". Tighten the screw again.

2. Tilt the saw head by 45° and verify the angle with a protrac-

tor (B).

If necessary, adjust the incline angle of the saw head with

the help of the set screw (11).

Working with the saw

Before starting to work consider the following safety advic-

es to keep the risk of injuries as small as possible.

 Saw blade OK?

 Workplace tidied?

 You may not start to operate the machine until you have

read these original instructions, observed all the instructions

given and installed the machine as described!

Before making adjustments to the saw settings (e.g. re-

placing the saw blade, setting the work piece stop, etc.)

− Switch off device

− Wait for standstill of the saw blade

− Pull out power plug

At any case pay attention to all security advices.

Loosen the transport locking pin before beginning work:

1. Slightly push the handle (3) down

2. Pull out the transport locking pin (5).

Safely support long work pieces with suitable means. For exam-

ple, use roller blocks or similar devices to support overhanging

work pieces.

Straight cuts

1. Bring the saw head into the vertical position and tighten the

incline fixing know (20).

2. Loosen die fixing screws for the rotary table (6) and turn the

saw head into the 0° position. Tighten the fixing screws for

the rotary table (6) again.

3. Place the work piece against the stop (7) and hold it firmly.

4. Switch on the saw

5. Wait until the saw blade has reached its full speed.

6. While holding the On/Off switch (2), pull the lock for the

pendulum cover (1) towards the handle.

7. Using the handle, gradually lower the saw head and cut

evenly through the work piece down to the slot in the rotary

table.

8. Hold the saw head in position until the saw blade is no long-

er in the work piece.

9. Release the On/Off switch and turn the saw head up again.

Mitre cuts

The mitre angle can be set left and right from 0° to 45°. The

table locks in place at frequently required positions.

1. Loosen the fixing screw for the rotary table (6) and turn the

saw head to the right or left to the desired angle.

2. Firmly tighten the fixing screw again.

3. Cut the work piece as described under "Straight cuts".

Inclinded cuts

The incline angle can be set 45° toward the left from the vertical

position (0°).

1. Loosen the incline fixing screw (20).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika KGS210N Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info