Bedienungsanleitung Atika KS2000 (Seite 22 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Finnisch)

475722

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

Commissioning

 Mains connection

 Compare the voltage given on the machine model plate

e.g. 230 V with the mains voltage and connect the saw

to the relevant and properly earthed plug.

 Use a shockproof plug, mains voltage 230 V with

residual current circuit breaker (FI switch 30 mA).

 Only use connection cables with sufficient diameters.

 Mains fuse

16 A insert

Electrical mains supply impedance

When conditions in the electrical mains supply are un-

favourable, voltage reductions for short periods can occur

during the process of turning on the equipment, which can

adversely affect other equipment (e.g., the flickering of a

lamp).

No breakdowns are to be expected if the maximum,

electrical mains supply impedances given in the table are

met.

Power consumption P

(W)

Electrical mains supply

impedance Z

max

(Ω)

2000 0,36

Switching On / Off

Do not use a device where

− the contactor can not be switched on and off.

− the chain and motor brake does not work properly

Damaged switches must be repaired or replaced

immediately by the customer service.

When switching on the chain saw must be supported

and held safely. Chain and sword must stand free.

Switch on

Push and hold automatic trip switch (5). Then operate the

On/Off switch (6). Release now automatic trip switch.

Switching off

Release On/Off switch.

Chain brake

The chain brake is a protective mechanism which in case

of a stroke back chain saw is initiated via the front hand

protection or after releasing the on/off switch. The saw

chain stops immediately (< 0,1 sec.).

Checking of chain brake

Check from time to time the function of the chain brake.

 Set the chain brake release (3) in pos. 2 and switch on

the chain saw.

Pos. 2 = Chain brake active

Chain saw does not initiate

 Set the chain brake release (3) in pos. 1 and switch on

the chain saw.

Pos. 1 = Chain brake released

Saw chain initiates

Clamping of saw chain

Check the saw chain tension before

 start of work

 after the first steps

 during sawing regularly all 10 minutes

☞ Only with a correct clamped saw chain and a sufficient

lubrication you can influence the durability.

 Please observe the following:

 a new saw chain must be reclamped more often until it

has elongated.

 in case of heating of chain to operating temperature it

expands and needs to be reclamped.

After finishing the sawing works release tension of

saw chain as in case of cooling too high tensions would

emerge in the saw chain.

 if chain flackers or comes out of the guide clamp it

again immediately.

Clamping of saw chain:

1. Put the chain saw with motor facing downward on an

even face.

2. Loosen the fastening screw (11) 1 – 2 revolutions anti-

clockwise.

3. Turn the chain tension ring (12) stepwise clockwise

until the correct chain tension is reached. The engaging

effect prevents that the chain tension loosens.

 The fastening screw (11) turns with it; possibly it

must be released again during the clamping process.

4. The saw chain is correctly clamped when it can be

lifted in the centre of the sword by appr. 3 – 4 mm.

5. Turn the chain tension ring (12) anti-clockwise when

the saw chain is clamped to much.

6. Refasten the fastening screw with the hand.

7. Check wether the chain links are positioned correctly in

the guide slot of the sword.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika KS2000 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info