Bedienungsanleitung Atika ST 200 (Seite 15 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch)

519344

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

 Wear protective clothing:

− ear protection (Sound intensity level at workplace can

exceed 85 dB (A))

− safety goggles

− gloves

− Dust protection mask when carrying out works that

produce a lot of dust

 Keep your workplace in an orderly condition! Untidiness

can result in accidents.

 Take into consideration environmental influences:

− Do not use the device in moist or wet ambience.

− Do not expose the radial tile cutter to rain.

− Provide for good illumination.

 Never leave the machine unattended.

 Children and youngsters less than 18 years of age and

people who have not read the operating manual must not

operate the machine.

 Keep other persons away.

Do not allow other persons, especially children, to touch

the tool or cable.

 Keep them away from your working area.

 Do not overload the machine! You work better and safer in

the given performance range.

 Only operate the machine with complete and correctly

attached safety equipment and do not alter anything on

the machine that could impair the safety.

 Do not use any cutting-off wheels which do not correspond

to the indicated characteristics of this instruction manual.

 Do not use any cutting-off wheels which have a maximum

rotational frequency of less than 3000 revolutions per

minute.



Pay attention to that the water pump is covered with water.

The use of other tools and other accessories can

signify a risk of injury for you.

 Switch the machine off and remove the mains plug from

the socket when

− carrying out repair works

− maintenance and cleaning

− Elimination of failures (that includes also freeing a

blocked cutting-off wheel)

− transport and storage

− Leaving the radial tile cutter (also for short-term

interruptions)

 Attention! Cutting-off wheel keeps running for a

moment after switching off! Do not brake the cutting-off

wheel with the hand or lateral pressure.

 Maintain your radial tile cutter with care:

− Keep the tools sharp and clean to be able to work

better and more safely.

− Follow the servicing instructions and the information

about changing tools.

− Keep handles dry and free of oils and grease.

 Check the machine for possible damage:

− Before continuing to use the machine, the protective

devices must be inspected to ensure that they work

perfectly and with their intended function

− Check whether the movable parts function perfectly

and do not stick or whether the parts are damaged, All

parts must be correctly installed and fulfil all conditions

to ensure perfect operation of the saw

− Damaged guards and parts must be properly repaired

or exchanged by a recognized, specialist workshop;

insofar as nothing else is stated in the instructions for

use.

− Damaged or illegible safety warning labels should be

replaced immediately.

 Do not allow any tool key to be plugged in!

 Store the unused machine in a dry locked place away

from the reach of children.

Electrical safety

 Design of the connection cable according to IEC 60 245

(H 07 RN-F) with a core cross-profile section of at least

− 1.5 mm

for cable lengths up to 25 m

− 2.5 mm

for cable lengths over 25 m

 Long and thin connection lines result in a potential drop.

The motor does not reach any longer its maximal power;

the function of the device is reduced.

 Plugs and coupler outlets on connection cables must be

made of rubber, non-rigid PVC or other thermoplastic

material of same mechanical stability or be covered with

this material.

 The connector of the connection cable must be splash-

proof.

 When running the connection line observe that it does not

interfere, is not squeezed, bended and the plug connection

does not get wet.

 Do not use the cable for purposes for which it is not meant.

Protect the cable against heat, oil and sharp edges. Do

not use the cable to pull the plug from the socket.

 Wind off completely the cable when using a cable drum.

 Regularly check the extension cables and replace them if

they are damaged.

 Do not use any defective connection cables.

 When working outdoors, only use extension cables

especially approved and appropriately labelled for outdoor

use.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 The device must be connected via the fitted PRCD

(residual-current-operated circuit breaker).

The electrical connection or repairs to electrical parts

of the machine must be carried out by a certified

electrician or one of our customer service points. Local

regulations – especially regarding protective measures –

must be observed.

Repairs to other parts of the machine must be carried out

by the manufacturer or one of his customer service

points.

Use only original spare. Accidents can arise for the user

through the use of other spare parts. The manufacturer

is not liable for any damage or injury resulting from such

action.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika ST 200 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika ST 200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info