Bedienungsanleitung Atika ST 200 (Seite 16 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch)

519344

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Preparing for commissioning

To achieve perfect function of the machine, follow the

notes given in these instructions

You have to attach the following parts:

 Base frame

 Cooling water pump

Assembly of the base frame and the cooling water

pump -

1. Assemble the main pillars (1) with the screws (4) and the

spring washers (5) on the frame.

2. Screw the clamp holders (6) with the star handle nuts (7)

and the coach bolts (8) on the frame (3).

3. Put the trough (9) into the frame (3).

4. Put the cooling water pump (26) into the intended gap of the

trough.

5. Fill water into the trough until the cooling water pump is

covered with water.

6. Put the radial tile cutter into the trough.

Commissioning

Mains connection

Compare the voltage given on the machine model plate e.g.

230 V with the mains voltage and connect the saw to the

relevant and properly earthed plug

Alternating current motor:

Use a shockproof plug, mains voltage 230 V with residual

current circuit breaker and 10 A inert fuses.

 Use connection cable or extension cable respectively with

a cross section of at least 1,5 mm².

Daily checks of the PRCD (residual-current-operated

circuit breaker)

The device must be connected via the residual-current-

operated circuit breaker (PRCD).

„Reset“

„Test“

Perform this check once in a

day.

When changing the location

no further test is required.

1. Directly plug the PRCD into the outlet (vertical).

2. Press the green Reset key – you will hear a click and the

indicator will light up orange.

3. To check the PRCD press the blue test key. The indicator

panel should no longer light.

4. Press the Reset key again – the indicator panel will

light up orange.

5. The machine can be startet.

Switch on

Do not use any device where the switch can not be

switched on and off. Damaged switches must be repaired

or replaced immediately by the customer service.

Check that the PRCD is operative: indicator panel orange.

Press the green button ( I ) on the

switch. At the same time, check

whether the rotating direction of the

cutting-off wheel corresponds to

the indicated rotational direction on

the protection cover (arrow).

If there is a power cut, the machine switches off automati-

cally. To switch on again, first press the red and then the

green button.

Switching off

Press the red button ( 0 ) on the switch.

Working instructions

Before commencing work, ensure the

following:

 Workplace tidied?

 Is the radial tile cutter stably mounted?

 You may not start to operate the machine until you have

read these operating instructions, observed all the

instructions given and installed the machine as described!

Working with the radial tile cutter

Keep your hands always in a safe distance to the

rotating cutting-off wheel.

 Do not start working before the cutting-off wheel has

reached its maximum rotational frequency.

 Pay attention to that the cooling water pump (26) washes

water to the cutting-off wheel.

 Only workpieces which have been securely mounted and

aligned can be processed.

Ensure that you always comply with the safety

instructions given on p. 13 ff.

Adjustments on the radial tile cutter

Replacing cutting-off wheel

Before replacing the cutting-off wheel pull

out the power plug.

 Do not use any damaged cutting-off wheels or such which

have changed their shape.

 Only use sharp cutting-off wheels.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika ST 200 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika ST 200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info