Bedienungsanleitung Atmos A25 (Seite 59 von 96) (Englisch)

810409

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Operation and maintenance manual - EN

www.atmos.cz EN-59

This method of pump controlling can be used for any ATMOS pellet boiler, and is therefore

recommended. AD02 or AD03 modules must be inserted and connected under the boiler hood

and the TK sensor must be installed before this function can be activated. After activation, S37,

S38, S39, S40 temperature parameters must be checked and configured.

n) S14 = 14….. Reserve function for direct control of solar heating pump from the burner regulation

(boiler terminal board). This function control solar pump when automatic sensor switching function

is activated (S15 = 3), where the boiler is connected with accumulation tank equipped with solar

exchanger and collectors. The system requires TV, TK, TS and solar sensors to be connected to the

TSV solar panel. This function never uses AD02 or AD03 modules.

After activation, S26, S27, S28, S29, S30, S31, S32, S33 temperature parameters must be checked

and configured.

This function is specially designed for boilers: D14P, P14, D15P, P15, D20P, P20, D21P, P21,

D25P and P25

CAUTION - the direct controlling function of solar heating from pellet burner cannot be

used for

DCxxSP(X)/(EP), CxxSP, ACxxSP

boilers and boilers with burner built into the

upper doors. This function also cannot be used when the pump is simultaneously controlled

in the boiler circuit from the burner regulation (TK sensor cannot be simultaneously in boiler

and accumulation tank)

o) S14 = 15….. Reserve function for the compressor control during the function for automatic

burner cleaning using compressed air. Power element designed for switching and powering the

compressor (e.g. contactor) must be connected between reserve output R2 and the compressor.

This function is connected with S6(14), S41, S42, S43, S44, S45, S46, S47 parameter, which must

be checked and configured.

p) S14 = 16….. Reserve function for controlling el.fan during the function for automatic burner

cleaning using compressed air. This function is connected with S6 (14), S41, S42, S43, S44, S45,

S46, S47 parameter, which must be checked and configured.

Special function for turning on reserve output R2 according to the temperature of a concrete sensor:

a) e.g. function: TS>… means that if the TS sensor temperature is higher then the set value in S52

parameter – Temperature C, reserve output R2 will be activated

b) e.g. function: TS<… means that if the TS sensor temperature is higher then the set value in

S52 parameter – Temperature C, reserve output R2 will be deactivated

c) e.g. function: TS, TV>… means that if the TS and TV sensor temperature is higher at the same

time then the set value in S52 parameter – Temperature C and S54 – Temperature D, reserve output

R2 will be activated (Temperature C = first position (TS), Temperature D = second position (Tv)).

d) e.g. function TS, TK<… means that if the TS and TK sensor temperature is higher at the same

time then the set value in S52 parameter – Temperature C and S54 – Temperature D, reserve output

R2 will be deactivated (Temperature C = first position (TS), Temperature D = second position

(Tk)).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A25 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atmos A25

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info