Bedienungsanleitung Atmos A25 (Seite 62 von 96) (Englisch)

810409

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

www.atmos.cz

62-EN

Operation and maintenance manual - EN

• Parameter S28 – deactivation difference of function S26 = 1… (3 K)

If the temperature on the solar panel (TSV) exceeds the temperature in the lower part of the tank

by the deactivation difference, the boiler deactivation function will be switched from the middle

TK sensor to the bottom TS sensor.

If a function for solar panel pump control is activated directly from the boiler regulation (S6 = 14

or S14 = 4), the same logic will be used to activate the solar pump.

• Parameter S29 – is the function for delaying the automatic switching from the TK sensor back to

the TS sensor for controlling the burner based on two temperatures (sensors, S15 = 3)... (0 hours)

This function will cause the function for deactivating the burner to be switched from the middle

TK sensor to the bottom TS sensor after the time listed in parameter S29 passes, if the temperature

on the solar panel TSV is lower or greater only by the deactivation difference (Parameter S28) than

the temperature in the lower part of the tank where the solar exchange is located.

The set value means the number of hours, e.g.: S29 = 2 means a switch delay of 2 hours.

• Parameter S30 – is the function of the minimal operating time of the solar pump when the

conditions for its activation and then deactivation are met (function S15 = 3)… (3 min )

The set value means the number of minutes, e.g.: S30 = 3 means 3 minutes

• Parameter S31 – characterizes the required temperature TS in the lower part of the accumulation

tank where the solar exchanger is located, during the function of charging the accumulation tank

by the solar collector. (function S15 = 3)… (75 °C)

Once it is reached, the solar pump will be turned off.

• Parameter S32 – characterizes the maximum temperature TV in the accumulation tank during the

function of charging the accumulation tank by the solar collector (function S15 = 3)… (100 °C)

The solar pump will be turned off if it is exceeded.

• Parameter S33 – characterizes the maximum temperature TSV of the solar collector, for which

the solar pump will still remain in operation (function S15 = 3) …(115 °C)

The solar pump will be turned off if it is exceeded.

• Parameter S34 – is the function of automatically starting the pellet burner (AUTOSTART) after

the wood burns out. The function is specially created for DCxxSP(X)/(EP), CxxS, ACxxSP burners,

however it may also be used for two separate boilers …. (0)

a) S34 = 0…. The automatic start function is off

b) S34 = 1…. The automatic start function is on. The pellet burner will be turned on when the

temperature of exhausts TSV drops below the set value (S36 = 80), e.g. below 80 °C

c) S34 = 2…. The automatic start function is on. The pellet burner will be turned on when two

conditions are met:

- the temperature of the boiler TK drops below the set value (S35 = 75), e.g. below 75 °C

- the temperature of exhausts TSV drops below the set value (S36 = 80), e.g. below 80 °C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A25 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atmos A25

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info