Bedienungsanleitung Atomos NinjaV (Seite 40 von 67) (Englisch)

769373

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

Atomos Ninja V – User Manual Edition 1: Aug 2021 38

MICROPHONE ICON: Where the audio source is set to HDMI Input, a

red microphone icon will appear next to the input number in the center of

the screen to indicate that the input is the current audio source. If there

is no audio coming from the input, a grey microphone will be displayed

instead. In Audio Follows Video (AFV) mode, a blue microphone icon will

be displayed next to the input that is the current audio source.

Where Mic/Line has been selected as the Audio Source, MIC/LIN will

appear at Audio at the top of the screen to indicate the mode. No

microphone icon is displayed over any of the inputs.

FADE IN / FADE OUT: These buttons can be used to fade in or fade out

of your program. You can set the color to fade to/from as White or Black

in the Switcher menu. Having dedicated Fade In/Out buttons gives you

complete control so that you can fade out from one input, switch to another

input and fade back in. Fading In/Out also applies an Audio fade effect.

Fading In/Out of the program stream is visible on the live stream over

USB-C and on displays connected to the HDMI Output on the AtomX

CAST. It is not recorded to the HDD/SSD.

QUAD SPLIT VIEW BUTTON: Tap to toggle between the multiview mode

where you can see all four inputs at once for switching, and the single input

view which displays one input at a time. The single input view is perfect for

checking and adjusting each input fullscreen, with the aid of the monitoring

tools. Tap the button again to return to the quad split view for switching.

SETTINGS: Pressing the settings button will take you to the corresponding

menu page for the current mode: PiP, Audio, Overlays and Switcher.

RECORD: Press to begin recording the program stream.

Program graphics, PiP and Fade In/Out cannot be recorded onto the

SSD/HDD in the Ninja V. To record these graphical elements, connect

an external recorder to PGM Out of the AtomX CAST

The LIVE button must be pressed to allow your program feed to be

output to your streaming software and/or connected Program display

via the CAST USB-C and CAST HDMI outputs. The LIVE button must

be enabled for either of these outputs to be active.

PLAY: Press to enter playback mode and play back the most recently

recorded clip. Tap RECORD to return to the switching/recording mode.

When you are live, the Playback button will be greyed out and

disabled. This ensures that the stream cannot accidentally be played

back during a live session.

MONITOR: Tapping Monitor in single input view mode reveals the

monitoring tools, so that you can switch between the camera inputs and

use the tools to check your shots. You can use scopes like the Waveform to

check exposure, Focus Peaking to check focus and Frame Guides to help

youframeyourcontentforaspecicaspectratioorforsocialmedia.For

more information, refer to the Monitoring & Recording section.

FADE IN / FADE OUT

QUAD SPLIT VIEW

SETTINGS

RECORD PLAY MONITOR PIP MODE AUDIO MODE OVERLAYS MODE SWITCHER MODE

8. Using the AtomX CAST - Main Screen

MICROPHONE ICON

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atomos NinjaV Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atomos NinjaV

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info