Bedienungsanleitung ATTACK DPX Combi Pellet (Seite 36 von 100) (Englisch)

810510

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

[ur 0] Operation of the additional output – this parameter defines the operating mode of the

additional output (pump for D.H.W. tank or accumulation tank warming).

[ur 0] Additional output without function – defines that the additional output and pump are

not connected and the additional output is not used in this case.

[ur 1] Priority D.H.W. tank warming – by this setting is the pump for D.H.W. tank warming

connected to the additional output and the sensor of D.H.W. is connected to the additional inlet.

Then, if the temperature in the D.H.W. tank decreases under the value of hysteresis

[uh 5] from the temperature adjusted [u 60], the pump of D.H.W. tank warming is started. After

the temperature in the D.H.W. tank reaches the set value [u 60], the pump is stopped. The pump

is also stopped, when the temperature in boiler is lower than the temperature in D.H.W. tank.

The [ur 1] mode means that the D.H.W. warming has priority, i.e. the pump of the heating circuit

is started after the D.H.W. is prepared.

[ur 2] Parallel charging the D.H.W. tank – similar principle as by the [ur 1], just the D.H.W. is

prepared by the parallel operation of the circuit pump of the heating circuit.

[ur 3] Unused

[ur 4] Charging the accumulation tank – due to this setting is the additional output used as

a pump to heat the accumulation tank and the additional sensor measures its temperature.

When the temperature in the boiler exceeds the hysteresis [uh 5] over the current temperature

of accumulation tank, the pump for charging is started. The pump is stopped, when the temper-

ature in the boiler is same or lower than the temperature in the accumulation tank, or when the

temperature in boiler decreases under the minimum boiler temperature defined by the parame-

ter [L 65].

[u 30] Operating temperature of the D.H.W. tank or accumulation tank – temperature to

control the additional output [ur ].

[uh 5] Hysteresis of the D.H.W. tank or accumulation – this parameter defines hysteresis of

the additional output [ur ].

[uP 5] Boiler temperature increase by D.H.W. preparation – this parameter is relevant, when

the additional output works under the mode of D.H.W. tank charging. It defines, for how many

degrees will the adjusted boiler temperature be higher than parameter [u 50] during the D.H.W.

tank warming.

[L 65] Minimum boiler temperature – defines the minimum boiler temperature that can be set

by a knob.

[H 85] Maximum boiler temperature – defines the maximum boiler temperature that can be

set by a knob.

[h 2] Hysteresis of boiler temperature – defines the difference between the adjusted and the

current boiler temperature for which must the boiler temperature decrease to start the control-

ler again after the adjusted boiler temperature is achieved.

[A 99] Temperature of boiler overheating – defines the value of boiler temperature to activate

the alarm of the boiler overheating.

[Fd60] Duration of boiler stop by ignition and fuel shortage – this parameter defines the

maximum time between starting the controller by the START button and achieving the control-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Combi Pellet Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info