Bedienungsanleitung ATTACK DPX Combi Pellet (Seite 57 von 100) (Englisch)

810510

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Settings:

The settings made during the installation are stored here, or it is

possible to reload the production or the installation settings.

Three main options are accessible:

„Loading of settings“ – means, that you can reset the original settings

„Saving of settings“ – stands for the final input of the burner settings, made by the installator.

This eases browsing of settings, if it would come to too many parameter changes.

„Production settings“ – are the original settings, that can be reloaded again.

Log:

All the errors are saved and displayed here, together with the

frequency of their incidence. Also the final number of the ignition

trials is here to be read.

There are four options: number of errors:

„Number of errors“ – displays every error code individually, e.g. E–CODE 10(X).

See the page for codes and explanation.

„Number of the first ignitions“ – displays, how many times did the ignition run.

„Number of the second ignitions“ – displays, how many second ignition trials were made by

burner (i.e. how many times did first trial fail).

„Last errors“ – displays the codes of errors in the order according to their incidence. It eases the

troubleshooting.

10 MAINTENANCE OF THE BOILER

During the boiler life is necessary to make maintenance to work properly. The maintenance fre-

quency depends on boiler frequency and utilization when is boiler in operation process.

Maitenance of the heating system with the boiler

It is necessary to check, eventually to refill the water in the heating system at least 1× in 14 days.

If the boiler is out of order during the winter period and danger the water could freeze in the

heating system, then the water should be replaced with an antifreeze mixture approved by the

producer or it should be discharged out of the system. Normally should be the water discharged

only in urgent cases and for ash short time as possible. At the end of the heating season it is nec-

essary to clean the boiler properly and to replace the damaged parts. Twice a year it is necessary

to dismantle the fan, to clean the radial impeller and to clean the fan air chamber.

Adjusting the hinges and exchange of the sealing cord of the door

After a particular period is the sealing cord in the door pressed. To ensure its tightness is neces-

sary to change the position of the door by screwing the door hinges. When the cord completely

loses its elasticity, or the hinges can no longer be moved into the direction to the boiler, it must

be replaced. Undo the worn sealing cord by the screw driver and clean the groove, where it was

laid. Take the new sealing cord and put its ends into the horizontal parts of the groove. Use your

hand, eventually a hammer to press the cord into the groove around the door. Loosen hinges

and find the correct position of door hinges to the door.

MENU/SETUP

ENTER < > EXIT

LOG

ENTER > EXIT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Combi Pellet Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info