Bedienungsanleitung ATTACK DPX Combi Pellet (Seite 58 von 100) (Englisch)

810510

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Replacement of the nozzle

The nozzle is laid in the boiler body on the holder. In the bottom part is the nozzle sealed by

a boiler sealant and in the upper part there is a sealing cord around. When replacing the nozzle,

remove the sealing cord from the groove by a screw driver. Take the nozzle out and clean the

holder properly from tar and old sealant. Then treat the bottom part of the nozzle with the fire-

proof sealant and put the nozzle on the clean holder with the arrow towards the rear boiler part.

There should be the same space on the both sides of the nozzle. Take the new set of the sealing

cords for the nozzle and press it lightly into the gap just around the nozzle.

10.1 BOILER CLEANING

The boiler must be cleaned regularly to operate correctly and reach the required comfort and

durability.

ATTENTION: The boiler has to be cleaned regularly and properly, otherwise there is a risk

of its wrong functionality, shortened service life or damage! The warranty is not valid if

the boiler is not regularly and sufficiently cleaned!

Cleaning the boiler should be carried out regularly and properly every 3 – 5 days because sedi-

mentation in the loading and combustion chamber with condensation and tar significantly re-

duce the life, power and efficiency of the boiler. If is bigger amount of ash than is not enough

space for burning out of fuel and this can damage the holder of ceramic jet as well as the whole

boiler. By boiler cleaning at first turn on the fan, open the feeding door and wipe the ash

through a slot into bottom space. Long pieces of unburned fuel leave in the hopper. Move

sometimes with the exchanger cleaning lever on the left side of the boiler. Ash and smoke put

out after opening the bottom cleaning hole. After opening the bottom door, clean the bottom

space. Interval of cleaning depends on the quality of wood (moisture), heating intensity, chim-

ney draft and other factors. We recommend to clean the boiler 1 time per week. Fireproof clay

do not take out by cleaning. Check the cleaning channel of primary and secondary air or cleaned

by scraping holes and blowing. It influences the output and quality of burning.

ATTENTION

Regular and proper cleaning is important to ensure the permanent output

and service life of the boiler. The warranty is not valid if the boiler is not sufficiently

cleaned and damaged.

The frequency of cleaning the particular boiler parts is given in the table below:

Cleaning*

Daily

Weekly Annually

Ash removing 1×

Space around the ash tray 1×

Space under the exchanger 1×

Lever of turbulators 5 – 6×

Flap 1×

Space of the fan 1×

Radial impeller of the fan 1×

* The minimum recommended intervals of cleaning. They can be shorter, according to the intensity of

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Combi Pellet Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info