Bedienungsanleitung ATTACK DPX (Seite 24 von 92) (Englisch)

810499

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

3.5 SETTING THE USER PARAMETERS

The menu for displaying and setting the user parameters is accessible after short pressing of the

OK button. The „+“ and „–“ buttons are used to browse in settings and parameters. The

appropriate parameter selected becomes adjustable by the „OK“ button and starts to flicker.

Then it can be changed by the „+“ and „–“ button and confirmed by „OK“. Some of the

parameters are only informative and they cannot be changed. To exit the menu, confirm the

[End] by „OK“ button. After remaining more than 1 minute without the user´s intervention, the

controller switches the display to the basic mode.

Table 2. User parameters:

Indication Parameter Min Max Step Prod. setting

C 45 Adjusted boiler temperature L65 H90 1 °C –

co C Operating mode of the circuit pump (‘C’ – WINTER, ‘–‘ –

SUMMER)

–

cu u Operation of the D.H.W. pump (‘u’ – casual mode, ‘d’ –

elimination of legionella bacteria) u d u

u50° Current temperature measured in the accumulation tank or

D.H.W. tank

150

Current flue gas temperature

End Exit from user parameters

[C 45] – Adjusted boiler temperature– this is the value of boiler water temperature the

regulator is going to reach while in the WORK mode. It is set by turning the thermostat knob

manually (8) and shown briefly on the display (6).

[co C] – WINTER/SUMMER mode – the winter mode is indicated by the ‘C’ letter. Then is the

circuit pump controlled by the room thermostat and distributes the heat into the heating

system. The summer mode is indicated by the „–“ sign. Then is the circuit pump out of order and

the heat generated by boiler is only used to heat the D.H.W. tank. If there is not D.H.W. tank in

the system (additional sensor is not connected), it is not possible to select the SUMMER / WINTER

mode.

[cu u] – Mode of D.H.W. tank warming –the regulator enables the casual D.H.W. tank warming

„u“ or the mode to eliminate the legionella bacteria „d“. After the „d“ mode is selected, the

temperature of 75 °C is achieved in the D.H.W. tank. When this temperature is achieved, the

controller switches into the mode of the casual D.H.W. tank warming „u“. The option of

elimination the legionella bacteria is not available, if the additional outlet and sensor are not set

for the D.H.W. warming.

CAUTION! Not to get hurt by the hot water, it is recommended to set this mode, when

the D.H.W. is not being used (e.g. during the night).

[u50°] Temperature of additional sensor– this is the value of current temperature of the

D.H.W. tank or of the accumulation tank of the heating system. This temperature is not displayed

in the user menu, if the additional output is not used.

[150°]Flue gas temperature – this value represents the current temperature of flue gas, if the

parameter for flue gas temperature is set in the service parameters.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK DPX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info