Bedienungsanleitung ATTACK DPX (Seite 26 von 92) (Englisch)

810499

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

3.7 DESCRIPTION OF PARAMETERS

[Π100]Maximum fan output – the highest fan output possible

[n 40]Minimum fan output – the lowest fan output possible

[Πh 5]Ratio of changing the fan rotations – this parameter influences the fan rotations, if the

adjusted boiler temperature is going to be achieved in a short time. For example, if the value 4 is

set, the fan will work at full output [Π100] (if the function of flue gas temperature control is not

active), up to 4 degrees before achieving the required boiler temperature. Then, by every

increase of the boiler temperature for 1 °C, the fan rotations are gradually decreased until the

minimum fan output is reached [n 40].

[Πr 0]Automatic regulation of changing the fan rotations – the fan rotations are increased /

decreased by setting this parameter within the range of 0 – 10 to ensure the required boiler

temperature. If this parameter is set to „- -“, the rotations are not controlled and the fan works at

full output according to the parameter [Π100]. Setting the parameter within the range of 0 – 10

relates to the time period (in minutes), during which are the fan rotations gradually increased

from the parameter of the minimum fan rotations [n 40] up to the parameter [r 100]. This

ensures the fluent heat-up of boiler.

[Πn 5]Frequency of exhaust fan blow-through – this frequency defines, how often the fan is

started to the full output [Π100] to take the flue gas out from the boiler, if the fan was stopped

due to the boiler temperature achieved.

[Πu 6]Duration of exhaust fan blow-through – during this period must the fan exhaust the

flue gas following the parameter [Πn 5].

[r 100]Fan output by ignition – this parameter defines the fan output by boiler heat-up. If the

parameter " Πr " is set to [Πr 0], then this parameter is not available.

[rh 5] Hysteresis of boiler stop by ignition – defines, how many degrees before reaching the

required boiler temperature will be the heat-up phase finished or (if the flue gas temperature

sensor is connected), how many degrees before reaching the required flue gas temperature are

relevant to stop the heat-up phase. After deactivation of the heat-up phase there is a casual

operating mode.

[P 30]Temperature to start the circuit pump – if there is not D.H.W. tank in the system [ur 0] or

it is in the mode [ur 2], then the parameter defines the boiler temperature for starting the circuit

pump of the heating system. If the parameter is set to „- -“, then too low temperature does not

influence the operation of the circuit pump. Anyway, the pump is always started, when the

boiler temperature exceeds the parameter [H 85] of the maximum boiler temperature.

If there is accumulation tank in the system (parameter [ur 4]), then this parameter defines the

temperature measured in the accumulation tank by which is the circuit pump of the heating

system started.

[Ph 2]Hysteresis of circuit pump – defines the temperature difference under which must the

boiler temperature or temperature in the accumulation tank decrease in comparison with the

temperature defined by the parameter

[P 30] to stop the circuit pump.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK DPX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info