Bedienungsanleitung ATTACK DPX (Seite 39 von 92) (Englisch)

810499

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

4.16 MAINTENANCE OF THE HEATING SYSTEM AND THE BOILER

It is necessary to check, eventually to refill the water in the heating system at least 1x in 14 days.

If the boiler is out of order during the winter period and the water could freeze in the heating

system, then the water should be replaced with an antifreeze mixture approved by the producer

or it should be discharged out of the system. Normally should be the water discharged only in

urgent cases and for ash short time as possible. At the end of the heating season it is necessary

to clean the boiler properly and to replace the damaged parts. Twice a year it is necessary to

dismantle the fan, to clean the radial impeller and to clean the fan air chamber.

Exchange of the sealing cord of the door

Undo the worn sealing cord by the screw driver and clean the groove, where it was laid. Take the

new sealing cord and put its ends into the horizontal parts of the groove. Use your hand,

eventually a hammer to press the cord into the groove around the door.

Adjusting the hinges

After a particular period is the sealing cord in the door pressed. To ensure its tightness is

necessary to change the position of the door by screwing the door hinges. The feeding door and

the bottom door are fixed to the boiler body by two hinges that are connected to the door by

a long joint. To adjust the hinges, it is necessary to remove the joint and to turn and to screw the

joint. Fix the door and put the joint into the hinge.

Replacement of the nozzle

The nozzle is laid in the boiler body on the holder. In the bottom part is the nozzle sealed by

a boiler sealant and in the upper part there is a sealing cord around. When replacing the nozzle,

remove the sealing cord from the groove by a screw driver. Take the nozzle out and clean the

holder properly from tar and old sealant. Then treat the bottom part of the nozzle with the

fireproof sealant and put the nozzle on the clean holder with the arrow towards the rear boiler

part. There should be the same space on the both sides of the nozzle. Take the new set of the

sealing cords for the nozzle and press it lightly into the gap just around the nozzle.

Adjustment of burning in the boiler

The burning is adjusted by the primary and secondary regulation flap. Producer sets the boilers

to the optimum conditions of burning with reference to the emissions and flue gas temperature.

Only the service staff trained by producer can make the adjustment.

Warning

It is not possible to use the warranty service to set the boiler combustion, to correctly set the

door, to replace the door seal and to replace the worn nozzle because of dependence

on the installation conditions, the wear and tear of the product, the product connection on the

chimney, and the type and quality of the fuel used!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK DPX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info