Bedienungsanleitung ATTACK SLX (Seite 15 von 120) (Englisch)

810506

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

5.4.1 USE OF ANTIFREEZE MIXTURE

It is not recommended to use antifreeze mixture with not suitable quality for the boiler opera-

tion. It is related especially to lowering the heat penetration, big volume expandability, aging,

rubber parts damage. If necessary, use the Alycol Termo (manufacturer Slovnaft Bratislava) anti-

freezing mixture – according to experiences of producer, there is no risk of lowering the safety of

use and noticeable influencing of the boiler work. If this type of protection against freezing is not

achievable in particular conditions, parameters are not fulfiled or there are some boiler failures

caused by use of other antifreezing mixtures, there is no possibility of warranty.

5.4.2 PROTECTION AGAINST CORROSION

Boiler must be connected with device for controlling the tempera-

ture of the boiler reverse. Suitable solution is use of mixing device

ATTACK – OVENTROP (Figure 2), which makes the temperature

rise of the return connection to acceptable level. In this way is

boiler protected against supercooling below 65 °C and creation of

the water steams, acids and tars in the feeding chamber is low-

ered. Mixing device ATTACK – OVENTROP allows to set tempera-

ture of return – water in range of ca. 50 – 70 °C thanks to the

thermostatic head.

Pic. 2 Device for protection of the reverse temperature

ATTACK OVENTROP

NOTICE: If the device against corrosion is not installed in the system or this device does

not work properly, there is a possibility of creation of agressive condensate, which might

lead to the boiler damage. Protection against condensation must be in use during the

boiler operation, otherwise is warranty provided by producer not valid!

Use of the size of ATTACK OVENTROP devices depending on the boiler output:

ATTACK OVENTROP DN25: SLX 20–35 kW

ATTACK OVENTROP DN32: SLX 40–55 kW

5.4.3 OUTFALL OF THE FLUE OUT OF THE BOILER

Flue has to have outfall to the chimney hole. If it is not possible to connect the boiler to the

chimney hole directly, then the appropriate extension should be as short as possible, of up to 1

m length, without any additional heating area and it must ascend to the chimney. It is good to

insulate the flue, to achieve sufficient flue gas temperature and prevent the chimney condensa-

tion. Flues must be mechanically firm (it is recommended to attach the flue to the boiler and bolt

them together) and tight against the flue leakage and cleanable inside. Flues must not lead

through the somebody else's dwelling or commercial premises. The internal diameter of the flue

must not taper in direction to the chimney. It is not eligible to use the elbow connectors. There

must be an „T – shaped“ connection between flue and chimney to let the condensate flow down

to the intended container and not in the boiler.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK SLX Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK SLX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info