Bedienungsanleitung Audiolab 8000AP (Seite 17 von 24) (Englisch)

496152

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

8c: Operation - 3

Volume Control

Mute

Altering the Front Speakers Balance

The knob, keys on the handset

control the level of all connected loudspeakers. They do not

affect the TAPE or DIGITAL OUT sockets

VOLUME VOLand the

Turn the knob clockwise to increase the volume or

anticlockwise to decrease the volume in 1dB steps. When you

reach either end of the volume range, you will still be able to

rotate the knob but the volume will stop changing.

The volume is alterable from (very low) to

( loud). The Volume level appears in the display. If you go

below -90dB the 8000AP will mute and the word MUTE will

appear in the display.

The 8000AP remembers the volume when put into

Standby and returns to this volume when next switched on. If

the last used volume is above -20dB, the 8000AP will power

on at a level of -20dB. This eliminates surprises caused by a

high previous volume setting.

To mute all speaker outputs press the button on the

front panel or the mute key on the remote control. To restore

the volume press MUTE again.

If you have turned the volume down manually below

the -90dB mark, the MUTE display will not turn on or off when

you press the key.

The 8000AP mutes momentarily whenever you change inputs

or undertake certain functions.

Press the BALANCE key on the front panel or the remote

control to enter Balance Mode

Alter the balance to the Right or Left by rotating the Volume

knob or the Left/Right keys on the handset.

keys

Press the key on the front panel or the remote

control to exit Balance Mode

If you do nothing, after a short period the 8000AP will

automatically exit Balance Mode.

įĬ

ǡǠ

VOLUME

-90dB +15dB

MUTE

Note:

MUTE

BALANCE

very

Note:

Keeping the

held down will move the sound progressively

further left or right

Night Mode

Forced Stereo Operation

Display On/Off

This mode works with Dolby Digital or DTS Digital Surround

sources which include Night Mode control parameters. Night

Mode reduces the dynamic range for quieter listening, so that

you can comfortably hear quieter passages at lower volume

levels -low levels are boosted, high levels are cut.

Press on the handset to toggle Night Mode

Pressing the key on the handset down-mixes a multi-

channel signal to a stereo (front left/right) signal only (the

stereo signal is created from all channels).

The subwoofer will appear in the Active Channels display if

the Front speakers have been set to Small or if the bass

management in the Setup menu has been set to L+R= to

Sub.

Pressing the key on the handset switches the display

off and on. When the 8000AP is operational and the display

is switched off only the Standby light remains on to show the

unit is active.

If you set the 8000AP to Standby when the display is switched

off, when you bring the unit out of Standby the display will

restore.

NIGHT MODE

On Off

STEREO

DISPLAY

Night Mode will remain active until it is switched off.

Always switch this mode off after use.

–

Page 15

VOLUME

MUTE

mute

3/3.1 ES Discrete

DVD VOL MUTE

–

Balance Control

L= 0.0dB R= 0.0dB

BAL

balance

Night Mode = On

Night Mode = Off

Stereo Mode

(Subwoofer Enabled)

Stereo Mode

(Subwoofer Disabled)

ENTERENTER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiolab 8000AP Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info