Bedienungsanleitung Audiosonic SCZT2 (Seite 22 von 32) (Englisch)

618699

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

VQT2R71

Functions and settings

Play

Functions and settings

To return to the previous

display/To cancel during setting

operation (

➜

page 23): Press

[

RETURN].

Using “WHISPER-MODE SURROUND”

This function is effective during surround playback only. You can enjoy the dynamic effect

even if the sound volume level is low during surround playback.

Press [WHISPER-MODE SURROUND] to select “W.S. ON ”.

• The current setting is displayed first.

Each time you press, the setting switches between “W.S. OFF ” and “W.S. ON ”.

 To cancel Press [WHISPER-MODE SURROUND] to select “W.S. OFF ”.

• WHISPER-MODE SURROUND is not effective in the following cases.

When not using the surround speakers:

When Dolby Virtual Speaker is off.

When using the surround speakers:

When Dolby Pro Logic

and SFC are off with 2-channel signal input.

• If the above setting is made when this function is on, this function temporarily becomes off.

Using “GAME”

Enjoy gaming with more dynamic sound.

Press [GAME].

• “GAME ” mode (

➜

page 19) in SFC is selected.

 To cancel Press again.

If cancelled, SFC’s effect itself is cancelled.

Muting

“MUTE ” blinks on the display while the volume is muted.

Press [MUTE].

 To cancel Press again.

• Muting is cancelled when you switch the system to standby.

• Muting is also cancelled when you adjust the volume.

Adjusting the bass (woofer part) output

When you feel the bass volume is not balanced with the volume of the front speakers, you

can adjust the bass during playback.

1. Press [CH] to select “WFR ”.

(The speaker is switched each time you press the button.)

WFR (woofer) → RS (surround right) (when used) → LS (surround left) (when used)

2. Press [SPEAKER LEVEL +, –] to adjust the bass volume.

Adjustment range: MIN, 1 to 15, MAX

Adjusting the surround speaker output

When using the surround speakers, you can adjust them, too.

1. Press [CH] to select “RS ” or “LS ”.

(The speaker is switched each time you press the button.)

WFR (woofer) → RS (surround right) → LS (surround left)

2. Press [SPEAKER LEVEL +, –] to adjust the volume of each

speaker.

Adjustment range: –10 to +10

 Repeat steps 1 and 2 to adjust the level of each speaker.

• You cannot adjust the front speakers with this operation. To adjust the volume balance

of left and right front speakers, see “Adjusting the volume balance of front speakers”.

(➜ page 23)

• If the sound is distorted, lower the level.

• You cannot adjust the output level of speakers if the sound field effect is off and the

speakers’ audio output is set to off. (

➜

page 19)

• You can adjust the speaker’s output level in SFC’s each mode respectively. (

➜

page 19)

• When a commercially available active subwoofer is connected to the subwoofer output

terminal on this unit’s rear panel, the subwoofer is synchronized with the unit and the

sound volume is adjusted.

Note

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiosonic SCZT2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Audiosonic SCZT2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info